Toshiba e-STUDIO160 Скачать руководство пользователя

Страница: 222 / 239

December 2002 TOSHIBA TEC

5 - 19

e-STUDIO160/200/250 UPDATING THE FIRMWARE

(11) When downloading ends, the following screen appears.

To perform downloading again:

→

Press the [Enter] key and follow the selected menu again.

To update the main data, proceed to step (4). (on page 5-15)

To update the scanner data, proceed to step (8). (on page 5-17)

To terminate the download program:

→

Press the [C] key while pressing the [Ctrl] key and follow step (12) and subsequent.

(12) Press the [Y] key.

05-03-024

(13) Turn the copier and PC power OFF.

Only when the main data is downloaded, perform the following operation to clear the memory.

(14) While pressing the [*] and [#] keys on the copier, turn the power ON and wait until "Please wait"

message is displyed.

(15) Turn the copier power OFF.

Содержание e-STUDIO160















































































































































































































































Результаты поиска

Содержание e-STUDIO160

Отзывы:

Похожие инструкции для e-STUDIO160

Бренды по названию

Популярные бренды

Toshiba e-STUDIO160, Руководство по обслуживанию

Результаты поиска

Содержание e-STUDIO160

Отзывы:

Похожие инструкции для e-STUDIO160

Бренды по названию

Популярные бренды