Toshiba e-STUDIO160 Скачать руководство пользователя

Страница: 20 / 239

e-STUDIO160/200/250 ADJUSTMENT ITEMS

1 - 12

December 2002 TOSHIBA TEC

Scan image processing parameter 600 DPI

Code

620

621

622

693

694

695

Factor

Image

quality

Image

quality

Image

quality

Density

Adjustment item

No. of units: HPF table number

0: Use of default value

1: Text/Photo mode

2: Photo mode

3: For Text mode

4 - 9: Unused

No. of tens: Filter combination intensity

0: Use of default value

1 - 9: Filter combination intensity

Ditto

Range correction on original set on the

ADF or RADF.

Set whether the value of the background

peak and text peak are fixed or not.

If they are fixed, the range correction is

performed with standard values.

The values of the background peak and

text peak affect the reproduction of the

background density and text density re-

spectively.

The number of units: Data while automatic

density is selected.

The number of tens: Data while manual

density is selected.

Background peak

Text peak

1: fixed

fixed

2: varied

fixed

3: fixed

varied

4: varied

varied

Image

mode

PPC

Image

quality

mode

Text/Photo

Photo

Text

Text/Photo

Photo

Text

Default

Acceptable

value *1

0-99

The larger the intensity

coefficient the stronger the

intensity.

0-99

11-14

21-24

31-34

41-44

Refer to

page

1-66

Содержание e-STUDIO160















































































































































































































































Результаты поиска

Содержание e-STUDIO160

Отзывы:

Похожие инструкции для e-STUDIO160

Бренды по названию

Популярные бренды

Toshiba e-STUDIO160, Руководство по обслуживанию

Результаты поиска

Содержание e-STUDIO160

Отзывы:

Похожие инструкции для e-STUDIO160

Бренды по названию

Популярные бренды