Toshiba e-STUDIO160 Скачать руководство пользователя

Страница: 187 / 239

December 2002 TOSHIBA TEC

4 - 65

e-STUDIO160/200/250 TROUBLESHOOTING

(7) Black banding (in feeding direction)

Step

Cause/Defect area

Scanner

Process unit

(main charger)

Process unit (Drum)

Fuser unit

Measures

Clean slit, lens and mirrors.

Clean charger wire.

Remove foreign matter.

Clean grid, replace process unit or grid.

Replace process unit or drum.

Clean or replace heat roller?

Replace process unit or fuser unit.

Check items

Foreign matter in optical path?

Main charger wire stained?

Foreign matter on grid?

Grid dirty or deformed?

Scratches on drum surface?

Dirt or scratches on heat roller

surface?

If problem persists after measures

are applied, or there is no prob-

lem found in above check, follow

procedure described in right col-

umn.

Feeding direction

Содержание e-STUDIO160















































































































































































































































Результаты поиска

Содержание e-STUDIO160

Отзывы:

Похожие инструкции для e-STUDIO160

Бренды по названию

Популярные бренды

Toshiba e-STUDIO160, Руководство по обслуживанию

Результаты поиска

Содержание e-STUDIO160

Отзывы:

Похожие инструкции для e-STUDIO160

Бренды по названию

Популярные бренды