Toshiba e-STUDIO160 Скачать руководство пользователя

Страница: 218 / 239

December 2002 TOSHIBA TEC

5 - 15

e-STUDIO160/200/250 UPDATING THE FIRMWARE

(3) Remove Disk 1 from the drive and insert Disk 2. Then press any key. The necessary files are copied

to the temporary area in the PC from Disk 2.

When copying is completed, the following screen appears.

05-03-019

The following operations are different depending on the menu selected in step (2).

When 1. Start PC Recovery (Main) is selected:

→

Refer to “Downloading procedure for main data.” (this page)

When 2. Start PC Recovery (Scanner Unit) is selected:

→

Refer to “Downloading procedure for scanner data.” (on page 5-17)

When 3. Start PC Recovery (Main + Scanner Unit) is selected:

→

Refer to “Downloading procedure for main data” and “Downloading procedure for scan-

ner data.”

Downloading procedure for main data: Steps (4) through (7)

(4) Turn the copier power OFF and connect it to the PC through the parallel cable.

(5) While pressing the [2], [*] and [#] keys on the copier, turn the power ON.

The following appears on the LCD.

05-03-020

Содержание e-STUDIO160















































































































































































































































Результаты поиска

Содержание e-STUDIO160

Отзывы:

Похожие инструкции для e-STUDIO160

Бренды по названию

Популярные бренды

Toshiba e-STUDIO160, Руководство по обслуживанию

Результаты поиска

Содержание e-STUDIO160

Отзывы:

Похожие инструкции для e-STUDIO160

Бренды по названию

Популярные бренды