Toshiba e-STUDIO160 Скачать руководство пользователя

Страница: 127 / 239

December 2002 TOSHIBA TEC

4 - 5

e-STUDIO160/200/250 TROUBLESHOOTING

Near the OCT

Is the OCT paper feed sensor working? (using the test mode 04, Sensor Test, DATA No. 9

Bit 4)

1. Check if each connector between the OCT paper feed sensor and the

OCT PWA (CN262) is disconnected.

2. Check if each connector between the JSP PWA (CN260) and the relay

PWA (CN41) is disconnected.

3. Check if each connector pin is removed or the harness is broken.

4. Check if any conductor pattern on the OCT, relay and main PWA is

open- or short-circuited.

5. Replace the OCT paper feed sensor.

6. Replace the OCT PWA.

7. Replace the Relay PWA.

8. Replace the main PWA.

Check to see if there are any foreign obstacles on the recording paper path.

E03

Paper remaining inside the machine at power ON

When recording paper is left inside the machine, remove it. If this error occurs frequently, refer

to E01 , E02 and E11 to E19 .

E08

Transporting jam inside the ADU

If recording paper is left in the ADU, remove it. If this error occurs frequently, the following items

should be checked.

Do the gears of the drive gear assembly rotate when the ADU motor (Upper) is driven in the

reverse direction? (using test mode 10, Output Test, CODE 224)

1.Replace the ADU PWA.

2.Replace the PFC PWA.

3.Replace the relay PWA.

4.Replace the main PWA.

YES

Содержание e-STUDIO160















































































































































































































































Результаты поиска

Содержание e-STUDIO160

Отзывы:

Похожие инструкции для e-STUDIO160

Бренды по названию

Популярные бренды

Toshiba e-STUDIO160, Руководство по обслуживанию

Результаты поиска

Содержание e-STUDIO160

Отзывы:

Похожие инструкции для e-STUDIO160

Бренды по названию

Популярные бренды