Toro TimeCutter SW 4200 Скачать руководство пользователя страница 7

Страница: 7 / 60

•

Replace all parts including, but not limited to, tires, belts,
blades, and fuel system components with original Toro
parts.

•

Check brake operation frequently. Adjust and service as
required.

Model 74675

Sound Pressure

This unit has a sound pressure level at the operator’s ear of 89
dBA, which includes an Uncertainty Value (K) of 1 dBA.

Sound power level was determined according to the
procedures outlined in EN ISO 5395:2013.

Sound Power

This unit has a guaranteed sound power level of 100 dBA,
which includes an Uncertainty Value (K) of 1 dBA.

Sound power level was determined according to the
procedures outlined in ISO 11094.

Vibration

Measured vibration level for right hand = 1.6 m/s

Measured vibration level for left hand = 1.6 m/s

Uncertainty Value (K) =0.8 m/s

Measured values were determined according to the procedures
outlined in EN ISO 5395:2013.

Whole Body Vibration

Measured vibration level = 0.60 m/s

Uncertainty Value (K) = 0.30 m/s

Measured values were determined according to the procedures
outlined in EN ISO 5395:2013. (Riding and Stand-Ons).

Model 74680

Sound Pressure

This unit has a sound pressure level at the operator’s ear of 93
dBA, which includes an Uncertainty Value (K) of 1 dBA.

Sound power level was determined according to the
procedures outlined in EN ISO 5395:2013.

Sound Power

This unit has a guaranteed sound power level of 105 dBA,
which includes an Uncertainty Value (K) of 1 dBA.

Sound power level was determined according to the
procedures outlined in ISO 11094.

Vibration

Measured vibration level for right hand = 1.7 m/s

Measured vibration level for left hand = 1.7 m/s

Uncertainty Value (K) = 0.8 m/s

Measured values were determined according to the procedures
outlined in EN ISO 5395:2013.

Whole Body Vibration

Measured vibration level = 0.48 m/s

Uncertainty Value (K) = 0.24 m/s

Measured values were determined according to the procedures
outlined in EN ISO 5395:2013 (Riding and Stand-Ons).

Содержание TimeCutter SW 4200





























































Результаты поиска

Содержание TimeCutter SW 4200

Отзывы:

Похожие инструкции для TimeCutter SW 4200

Бренды по названию

Популярные бренды

Toro TimeCutter SW 4200, Руководство оператора

Результаты поиска

Содержание TimeCutter SW 4200

Отзывы:

Похожие инструкции для TimeCutter SW 4200

Бренды по названию

Популярные бренды