Toro TimeCutter SW 4200 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 60

background image

Maintenance

Note:

Determine the left and right sides of the machine from the normal operating position.

Recommended Maintenance Schedule(s)

Maintenance Service

Interval

Maintenance Procedure

After the first 5 hours

• Change the engine oil.

Before each use or daily

• Check the engine-oil level.
• Clean the air-intake screen.
• Check the cutting blades.
• Inspect the grass deflector for damage

After each use

• Check and clean the front of the machine.
• Clean the mower-deck housing.

Every 25 hours

• Grease all the lubrication points.
• Clean the foam element (more often in dusty, dirty conditions).
• Check tire pressure.
• Check the belts for wear or cracks.

Every 100 hours

• Replace the foam element (more often in dusty, dirty conditions).
• Service the paper element (more often in dusty, dirty conditions).
• Change the engine oil (more often in dusty, dirty conditions).
• Change the oil filter (more often in dusty, dirty conditions).
• Check the spark plug(s).
• Check the in-line fuel filter.

Every 200 hours

• Replace the paper element (more often in dusty, dirty conditions).
• Replace the spark plug(s).
• Replace the in-line fuel filter.

Before storage

• Charge the battery and disconnect battery cables.
• Perform all maintenance procedures listed above before storage.
• Paint any chipped surfaces.

CAUTION

If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure
you or other bystanders.

Remove the key from the ignition and disconnect the wire from the spark plug before you do any
maintenance. Set the wire aside so that it does not accidentally contact the spark plug.

32

«
...
30
31
32
33
34
...
»

Содержание TimeCutter SW 4200





























































Отзывы:

Нет отзывов

Похожие инструкции для TimeCutter SW 4200

Бренд: Yard Machines Страницы: 20

Бренд: Toro Страницы: 2

Бренд: Ryobi Страницы: 192

Бренд: Yazoo Страницы: 9

Бренд: Gardenline Страницы: 36

Бренд: Jacobsen Страницы: 36

Бренд: Spearhead Страницы: 64

Бренд: Bad Boy Страницы: 20

Бренд: Woods Страницы: 76

Бренд: Gama Garden Страницы: 19

Бренд: Ransomes Страницы: 184

Бренд: Weed Eater Страницы: 48

Бренд: Walker Страницы: 92

Бренд: Scag Power Equipment Страницы: 20

Бренд: Urrea Страницы: 40

Бренд: Einhell Royal Страницы: 24

Mowers DIESEL 1500cc

Бренд: Bad Boy Страницы: 54

Бренд: Wards Garden Mark Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды