Toro TimeCutter SW 4200 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 60

background image

Figure 22

1.

Discharge cover

3.

Bolt (1/4 x 2-1/2 inches)

2.

Cap nut (1/4 inch)

6.

Secure the discharge cover to the lower lip of the
mower with 2 bolts (1/4 x 2-1/2 inches) and 2 cap nuts
(1/4 inch) as shown in

Figure 22

.

Note:

Do not overtighten the nuts; this could distort

the cover and cause blade contact.

Converting to Side Discharge
(for models with 127 cm
(50-inch) decks)

The mower deck and mower blades shipped with this machine
were designed for optimum mulching and side discharge
performance.

Removing the Right Baffle for Side
Discharge

1.

Park the machine on a level surface and disengage the
blade-control switch.

2.

Ensure the parking brake is engaged, stop the engine,
remove the key, and wait for all moving parts to stop
before leaving the operating position.

3.

Remove the right mower blade; refer to

Removing the

Blades (page 44)

.

4.

Remove the 2 knobs and curved washers that secure
the right baffle to the mower (

Figure 23

).

Figure 23

1.

Knob

3.

Baffle stud coming through
the mower

2.

Curved washer

5.

Remove the right baffle and lower the grass deflector
over the discharge opening as shown in

Figure 23

and

Figure 24

.

Figure 24

1.

Right baffle

3.

Discharge opening

2.

Curved washer and knob

6.

Install fasteners into the holes in the top of the mower
to prevent flying debris.

27

«
...
25
26
27
28
29
...
»

Содержание TimeCutter SW 4200





























































Отзывы:

Нет отзывов

Похожие инструкции для TimeCutter SW 4200

Бренд: Lawn-Boy Страницы: 84

Бренд: Toro Страницы: 56

pro-turn 460 diesel 992236

Бренд: Gravely Страницы: 51

Бренд: Viking Страницы: 36

Бренд: Baroness Страницы: 66

CheckMate 21462

Бренд: Big League Lawns Страницы: 4

Бренд: Yard force Страницы: 30

Бренд: Dolmar Страницы: 120

Blizzard 17,5 H

Бренд: EMAK Страницы: 338

Бренд: Simplicity Страницы: 16

Бренд: Simplicity Страницы: 22

Бренд: Simplicity Страницы: 32

Бренд: Gardena Страницы: 15

Бренд: Raider Страницы: 76

Бренд: Agria Страницы: 42

Super Recycler 20837

Бренд: Toro Страницы: 84

Country Clipper SR1215

Бренд: Boss Страницы: 27

Бренд: Exmark Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды