Toro TimeCutter SW 4200 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 60

background image

wrench for removing and installing the spark plug(s) and a
gapping tool/feeler gauge to check and adjust the air gap.
Install a new spark plug(s) if necessary.

Type:

Champion RN9YC

Air gap:

0.76 mm (0.03 inch)

Removing the Spark Plug

1.

Disengage the PTO and ensure the parking brake is
engaged.

2.

Stop the engine, remove the key, and wait for all moving
parts to stop before leaving the operating position.

B

A

g027478

Figure 40

Note:

Due to the deep recess around the spark plug,

blowing out the cavity with compressed air is usually
the most effective method for cleaning. The spark plug
is most accessible when the blower housing is removed
for cleaning.

Checking the Spark Plug

Important:

Do not clean the spark plug(s). Always

replace the spark plug(s) when it has: a black coating,
worn electrodes, an oily film, or cracks.

If you see light brown or gray on the insulator, the engine is
operating properly. A black coating on the insulator usually
means the air cleaner is dirty.

Set the gap to 0.76 mm (0.030 inch).

B

A

g027479

Figure 41

Installing the Spark Plug

Tighten the spark plug(s) to 25–30 N-m (18.5–22.1 ft-lb).

B

A

25-30 N-m

18.5-22.1 ft-lb

g027960

C

D

Figure 42

Cleaning the Cooling System

Clean the air-intake screen from grass and debris before each
use.

1.

Disengage the blade-control switch and ensure the
parking brake is engaged.

2.

Stop the engine, remove the key, and wait for all moving
parts to stop before leaving the operating position.

3.

Remove the air-intake screen, the air-cleaner cover, and
the fan housing.

4.

Clean debris and grass from the parts.

5.

Install the air-intake screen, air-cleaner cover, and the
fan housing.

38

«
...
36
37
38
39
40
...
»

Содержание TimeCutter SW 4200





























































Отзывы:

Нет отзывов

Похожие инструкции для TimeCutter SW 4200

SABO 43-COMPACT E

Бренд: Sabo Страницы: 116

Бренд: Sabre Страницы: 191

Бренд: MTD Страницы: 4

Бренд: Sears Страницы: 56

Бренд: Yard-Man Страницы: 36

Бренд: LawnMaster Страницы: 40

Hydrostatic Vergecutter 76

Бренд: Ransomes Страницы: 54

Бренд: Yard Machines Страницы: 72

Craftsman 944.601181

Бренд: Sears Страницы: 52

Бренд: Ransomes Страницы: 134

Бренд: Poulan Pro Страницы: 31

Patriot FDR1660

Бренд: Land Pride Страницы: 2

Бренд: Alamo Industrial Страницы: 186

Бренд: Aerotek Страницы: 18

Бренд: Yard Machines Страницы: 16

Бренд: MID WEST PRODUCTS Страницы: 4

Бренд: Webb Страницы: 24

Бренд: Bad Boy Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды