Toro TimeCutter SW 4200 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 60

background image

Electrical System
Maintenance

WARNING

CALIFORNIA

Proposition 65 Warning

Battery posts, terminals, and related

accessories contain lead and lead compounds,

chemicals known to the State of California

to cause cancer and reproductive harm.

Wash hands after handling.

Charging the Battery

Removing the Battery

WARNING

Battery terminals or metal tools could short against
metal machine components causing sparks. Sparks
can cause the battery gasses to explode, resulting
in personal injury.

•

When removing or installing the battery, do not
allow the battery terminals to touch any metal
parts of the machine.

•

Do not allow metal tools to short between
the battery terminals and metal parts of the
machine.

1.

Park the machine on a level surface and disengage the
blade control switch.

2.

Ensure the parking brake is engaged, stop the engine,
remove the key, and wait for all moving parts to stop
before leaving the operating position.

3.

Raise the seat to access the battery.

4.

Disconnect the negative (black) ground cable from the
battery post (

Figure 44

). Retain all fasteners.

WARNING

Incorrect battery cable routing could damage
the machine and cables causing sparks.
Sparks can cause the battery gasses to
explode, resulting in personal injury.

•

Always disconnect the negative (black)
battery cable before disconnecting the
positive (red) cable.

•

Always connect the positive (red) battery
cable before connecting the negative
(black) cable.

5.

Slide the rubber cover up the positive (red) cable.
Disconnect the positive (red) cable from the battery
post (

Figure 44

). Retain all fasteners.

6.

Remove the battery hold-down (

Figure 44

) and lift the

battery from the battery tray.

G005072

1

2

3

4

5

6

7

Figure 44

1.

Battery

5.

Negative battery post

2.

Positive battery post

6.

Wing nut, washer, and bolt

3.

Bolt, washer, and nut

7.

Battery hold-down

4.

Terminal boot

Charging the Battery

Service Interval:

Before storage—Charge the battery and

disconnect battery cables.

1.

Remove the battery from the chassis; refer to Removing
the Battery.

2.

Charge the battery for a minimum of 1 hour at 6 to 10
amps. Do not overcharge the battery.

3.

When the battery is fully charged, unplug the charger
from the electrical outlet, then disconnect the charger
leads from the battery posts (

Figure 45

).

40

«
...
38
39
40
41
42
...
»

Содержание TimeCutter SW 4200





























































Отзывы:

Нет отзывов

Похожие инструкции для TimeCutter SW 4200

Бренд: Simplicity Страницы: 11

Бренд: Yard-Man Страницы: 12

Бренд: Vicon Страницы: 16

Бренд: Craftsman Страницы: 56

Бренд: Craftsman Страницы: 56

Бренд: Craftsman Страницы: 56

Бренд: Craftsman Страницы: 56

Бренд: Craftsman Страницы: 56

Бренд: Craftsman Страницы: 56

Бренд: Craftsman Страницы: 56

Бренд: Craftsman Страницы: 56

Бренд: Craftsman Страницы: 60

Бренд: Craftsman Страницы: 56

Бренд: Craftsman Страницы: 60

Бренд: Craftsman Страницы: 60

Бренд: Craftsman Страницы: 60

Бренд: Craftsman Страницы: 60

Бренд: Craftsman Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды