Toro TimeCutter SW 4200 Скачать руководство пользователя страница 54

Страница: 54 / 60

Problem

Possible Cause

Corrective Action

1. The engine mounting bolts are loose.

1. Tighten the engine mounting bolts.

2. The engine pulley, idler pulley, or blade

pulley is loose.

2. Tighten the appropriate pulley.

3. The engine pulley is damaged.

3. Contact an Authorized Service Dealer.

4. The cutting blade(s) is/are bent or

unbalanced.

4. Install a new cutting blade(s).

5. A blade mounting bolt is loose.

5. Tighten the blade mounting bolt.

There is abnormal vibration.

6. A blade spindle is bent.

6. Contact an Authorized Service Dealer.

1. The blade(s) is not sharp.

1. Sharpen the blade(s).

2. A cutting blade(s) is/are bent.

2. Install a new cutting blade(s).

3. The mower is not level.

3. Level the mower from side-to-side and

front-to-rear.

4. An anti-scalp wheel is not set correctly.

4. Adjust the anti-scalp wheel height.

5. The underside of the mower is dirty.

5. Clean the underside of the mower.

6. The tire pressure is incorrect.

6. Adjust the tire pressure.

Uneven cutting height.

7. A blade spindle is bent.

7. Contact an Authorized Service Dealer.

1. The drive belt is worn, loose or broken.

1. Install a new drive belt.

2. The drive belt is off of the pulley.

2. Install the drive belt and check the

adjusting shafts and belt guides for the
correct position.

3. The Power Take-Off (PTO) switch or

PTO clutch is faulty.

3. Contact an Authorized Service Dealer.

The blades do not rotate.

4. The mower belt is worn, loose, or

broken.

4. Install a new mower belt.

Содержание TimeCutter SW 4200





























































Результаты поиска

Содержание TimeCutter SW 4200

Отзывы:

Похожие инструкции для TimeCutter SW 4200

Бренды по названию

Популярные бренды

Toro TimeCutter SW 4200, Руководство оператора

Результаты поиска

Содержание TimeCutter SW 4200

Отзывы:

Похожие инструкции для TimeCutter SW 4200

Бренды по названию

Популярные бренды