Toro TimeCutter SW 4200 Скачать руководство пользователя страница 41

Страница: 41 / 60

Figure 45

Positive battery post

Red (+) charger lead

Negative battery post

Black (-) charger lead

Installing the Battery

Position the battery in the tray (

Figure 44

Install the positive (red) battery cable to the positive (+)
battery terminal using the fasteners removed previously.

Install the negative battery cable to the negative (-)
battery terminal using the fasteners removed previously.

Slide the red terminal boot onto the positive (red)
battery post.

Secure the battery with the hold-down (

Figure 44

Lower the seat.

Servicing the Fuses

The electrical system is protected by fuses. It requires
no maintenance; however, if a fuse blows, check the
component/circuit for a malfunction or short.

Fuse type:

•

Main—F1-30 amp, blade-type

•

Charge Circuit—F2-25 amp, blade-type

Remove the screws securing the control panel to the
machine.

Note:

Retain all fasteners.

Lift the control pane up to access the main wiring
harness and fuse block (

Figure 46

To replace a fuse, pull out on the fuse to remove it
(

Figure 46

G014921

Figure 46

Main—30 amp

Charge circuit—25 amp

Return the control panel to its original position.

Note:

Use the screws removed previously to secure

the panel to the machine.

Содержание TimeCutter SW 4200





























































Результаты поиска

Содержание TimeCutter SW 4200

Отзывы:

Похожие инструкции для TimeCutter SW 4200

Бренды по названию

Популярные бренды

Toro TimeCutter SW 4200, Руководство оператора

Результаты поиска

Содержание TimeCutter SW 4200

Отзывы:

Похожие инструкции для TimeCutter SW 4200

Бренды по названию

Популярные бренды