background image

 

11

 

 

1.4.2.2 The turnstile’s status (

Fig

. 5

) is displayed by the LEDs 

1,2,

 installed on the pedestal 

frame  elements.  Constantly  lit  blue  LED  means  the  turnstile  initial  state.  In  case  of  attempt  of 
unauthorized  access  red  LED  starts  blinking  and  sound  signal  is  generated.  When  opening 
command is received, signal is transformed to green arrow from the side of authorized access. If 
unauthorized  access  is  attempted  when  blades  are  open,  the  blades  will  close  if  there  is  no  any 
obstacle in the blade movement area

1.4.2.3 

Seven  infrared  sensors 

3

,  located  on  the  turnstile  side  panels  from  access  side,  are 

designed  for  detection  of  the  turnstile  access,  preventing  closing  of  blades  during  pedestrian 
access  in  immediate  proximity  to  them  and  minimizing  potential  for  injury  during  the  turnstile 
access. 

1.4.2.4 Blade 

4

 is made from 10 mm thick tempered glass and is located in the middle of the 

pedestal body, pivotally connected with actuator. Each blade is actuated by separate servomotor. 
Additional  pedestal  is  equipped  with  two  servomotors  (one  per  each  access  way),  while  margin 
pedestals (left-hand and right-hand) are equipped with one servomotor. 

1.4.2.5 In case of 230V main power failure the turnstile blades will remain in the position in 

which they were, and the turnstile operation will be maintained from battery (if available). 

1.4.2.6  The  pedestal  crank-and-rocker  mechanism,  shown  in  Figure  5,  provides  reciprocal 

movement of the pedestal telescopic glass blade. 

1.4.2.7  Inside  the  turnstile  body  the  panels  are  fixed  on  which  controllers,  power  supply 

unit, battery and terminal blocks to be connected to 230V mains and control devices are located. 

Controllers РСВ.201.01.00.00 control the turnstile motors analyzing signals from magnetic 

sensor,  and  provide  motor  overload  protection.  Controllers  analyze  infrared  sensors,  receive 
control commands from peripherals (control panel, ACS etc.), control LED displays and generate 
feedback signals for ACS.  

1.4.2.8 External control panel has the following functions: single entry and single exit, entry 

and exit LOCK, free entry and exit 

1.4.3 Principle of operation 

1.4.3.1 Access cycle: 

 

1. 

In the initial  state the turnstile glass blades are located perpendicular to the body block 

access.

 

2.  The  turnstile  is  opened  for  access  in  the  direction  "А"  or  "В"  after  the  appropriate 

command from ACS or control panel is issued. 

3.  Green  arrow  is  lit  on  LED  display  and  glass  blades  go  fully  to  slots,  i.e.  they  open.  A 

pedestrian is able to access through the turnstile freely. 

4.After  pedestrian  exit  from  control  area,  the  "closed"  mode  is  set  until  next  access.  Blue 

LED is lit. Blades are reliably closed preventing attempts of unauthorized access. 

More  detailed  description  of  the  turnstile  operation  modes  is  given  in  section  1.6 

"Description and operation of controller as an integral component of the turnstile". 

 
1.4.3.2 

12V DC power voltage is provided by power supply unit.

 

1.4.3.3 

In  case  of  mains  power  supply  failure,  the  turnstile  is  automatically  switched  to 

power supply from 12V, 7A•h battery (optional), which ensures the turnstile's operation within 2 
hours.

 

1.4.3.4 

The turnstile wiring and connection diagrams are shown in Annex C.

 

Содержание SpeedBlade T3.KCD.XV.X Series












































Отзывы: