THORLABS LPS710/M Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 70

background image

55

Appendix B Preventive Maintenance

B.1 Safety Testing

PAT testing in accordance with local regulations, should be performed on a regular

basis, (typically annually for an instrument in daily use).

B.2 Cleaning

The fascia may be cleaned with a soft cloth, lightly dampened with water or a mild

detergent.

Warning

The top platform must not be removed. Slacking of the top platform

attachment nut will cause internal damage and will invalidate the warranty.

Shock Warning

The equipment contains no user servicable parts. There is a risk of electrical

shock if the equipment is operated with the covers removed. Only personnel

authorized by Thorlabs Ltd and trained in the maintenance of this equipment

should remove its covers or attempt any repairs or adjustments. Maintenance

is limited to safety testing and cleaning as described in the following sections.

Warning

Disconnect the power supply before cleaning the unit.

Never allow water to get inside the case.

Do not saturate the unit.

Do not use any type of abrasive pad, scouring powder or solvent, e.g.

alcohol or benzene.

«
...
53
54
55
56
57
...
»

Содержание LPS710/M







































































Отзывы:

Нет отзывов

Похожие инструкции для LPS710/M

Бренд: Samson Страницы: 36

Бренд: FBII Страницы: 71

Бренд: CAME Страницы: 4

Бренд: Eaton Страницы: 6

Бренд: Bard Страницы: 8

Бренд: Bardiani Valvole Страницы: 35

Бренд: Datalogic Страницы: 15

Бренд: Hama Страницы: 17

Бренд: OES Страницы: 3

Бренд: KEENZ Страницы: 68

Бренд: UNISENSE Страницы: 16

Бренд: Xylem Страницы: 48

Frigolink FVB110B

Бренд: WURM Страницы: 4

traxon e:cue LCE-mx

Бренд: Osram Страницы: 35

Бренд: FEAS Страницы: 4

Liquitron DP5000-01A

Бренд: LMI Technologies Страницы: 28

Бренд: Motrona Страницы: 10

PSS67 IO1 16FDI

Бренд: Pilz Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды