manualshive.com logo in svg

THORLABS LPS710/M, Руководство пользователя

Поделиться
Скачать
THORLABS LPS710/M Скачать руководство пользователя страница 33

33

LPS710E Long Travel Piezo Stage and Controller

5) Click ‘OK’ to save the settings and close the window.
Any  voltage  on  the  rear  panel  BNC  connector  is  now  amplified  by  the  unit  and

presented at the STAGE (drive) connector. The position of the piezo stage in closed

loop mode (0 to 800 µm) can be controlled by varying the 0-10V external source.

4.8 Thermal Shutdown

In  order  to  protect  the  piezo  driver  card  from  overheating  due  to  abnormal  load

conditions, the electronics contains thermal protection circuitry. When the protection

is activated, the HV output its shut down, limiting the maximum output current to a few

milliamps, and the ‘Error’ LED on the GUI panel lights, warning the user of the fault

condition.  If  the  overtemp  condition  occurs,  turn  off  the  controller  and  allow  10

minutes for the unit to cool down.

Caution

When driving the piezo stage from an external source, the external signal 

is added to the software input (GUI panel or SetVoltOP software method) 

and, if connected and selected, the Joystick. 

In closed loop a drive voltage of 120V gives around 800 µm travel, in open 

loop the drive voltage can be as high as 150 V with a travel of 1100 µm. 

When using an external source and switching from open loop to closed 

loop, care must be taken that the travel range is not pushed to its limit. If 

closed loop is selected with excessive drive voltages applied, the stage 

may jump position and/or drift.

Note

When the software contribution is 0µm and the unit is in closed loop, 0-10V will  

correspond to 0 to 800um and each 1V BNC corresponds to 80um. 

If the software contribution is set to 400um for example, the unit can then be 

driven  from 0 to 800um by +/-5V via Ext BNC. A software offset of 800um, 

would then require -10 to 0V at the BNC to drive the unit.

Содержание LPS710/M







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды