THORLABS LPS710/M Скачать руководство пользователя страница 14

Страница: 14 / 70

HA0378T Rev C Feb 2019

Chapter 3

3.3 Mounting

3.3.1 General

3.4 Installing the Stage

The stage features several mounting options as shown below. Please search

LPS710E at www.thorlabs.com for detailed dimension drawings.

Fig. 3.3 Attaching the LPS710 stage

Note

This handbook has been compiled to support the LPS710 piezo actuator and

PPC001 controller as a matched pair in a standalone system. For assistance

with integration into third party systems, please contact tech support.

Cautions

When mounting the stage within the application, ensure that the travel is not

obstructed. The moving world moves down as the voltage is increased. If the stage

is driven against a solid object, damage to the internal mechanism could occur.

The range of travel is 800 µm in closed loop but can be up to 1100 µm (± 10%) in

open loop.

When considering movement in the proximity of other objects or equipment,

ensure that movement of cables connected to the stage is not impeded.

To fit M6 (1/4"-20)
Cap Screw, 2 Places

To fit M4 (4-40)
Cap Screw, 4 Places

Side Mounting Holes
M3 x 0.5 (4-40), 4.5 mm (0.18”) Depth
2 Places on each face

Bottom Mounting Holes
M3x 0.5 (4-40), 4.2 mm (0.17”) Depth
2 Places

Содержание LPS710/M







































































Результаты поиска

Содержание LPS710/M

Отзывы:

Похожие инструкции для LPS710/M

Бренды по названию

Популярные бренды

THORLABS LPS710/M, Руководство пользователя

Результаты поиска

Содержание LPS710/M

Отзывы:

Похожие инструкции для LPS710/M

Бренды по названию

Популярные бренды