THORLABS LPS710/M Скачать руководство пользователя страница 39

Страница: 39 / 70

LPS710E Long Travel Piezo Stage and Controller

Chapter 5 Software Reference

5.1 GUI Panel

The following screen shot shows the graphical user interface (GUI) (one panel per

card fitted) displayed when accessing the controller using the APTUser utility.

Fig. 5.1 PPC001 Piezo Driver Software GUI

Output Control

- used to adjust and set the voltage or position output as displayed in

the main digital display. If the channel is in closed loop mode (set using the 'closed

loop' button on the panel) then this control can be used to adjust position output. If

open loop mode is selected (using the 'open loop' button) then the control is used to

adjust the voltage output. Note that the read out in the main digital display is

independent of the operating mode (open or closed loop) selected for the particular

channel. If the 'Volts' button is selected, then the read out is in volts, even if the channel

is in closed loop mode and the Output control is being used to adjust position.

Similarly, if the 'position' button is selected, the read out is in microns, derived from the

feedback signal, even if the channel is operating in open loop.

Jog

- used to increment or decrement the piezo position. When the button is clicked,

the piezo is driven in the selected direction, one step per click. The step size can be

set in the 'Settings' panel or by using the SetJogStepSize method.

Note

The serial number of the PPC001 unit associated with the GUI panel, the

APT server version number, and the version number (in brackets) of the

embedded software running on the unit, are displayed in the top right

hand corner. This information should always be provided when

requesting customer support.

Содержание LPS710/M







































































Результаты поиска

Содержание LPS710/M

Отзывы:

Бренды по названию

Популярные бренды

THORLABS LPS710/M, Руководство пользователя

Результаты поиска

Содержание LPS710/M

Отзывы:

Бренды по названию

Популярные бренды