THOMSON DD10, Руководство по установке

Страница: 145 / 179

8. DVE and Editors DD5, DD10, DD20, DD30
136
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
Assignment for
DD20 and DD30
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Required for mode 1 only.
As two DVE devices may be connected to the switchers, the DVE(s) must be
assigned to the switching levels MEx/PP. One DVE may be assigned to several
MEs.
If only one DVE is connected, this must be assigned as well. It may be assigned to
any ME and the PP stage. Any assignment will remain stored until the assignment
is changed. Before the assignment, a port for the DVE must be defined by port
number and port protocol in the Setup.
Assignment is made as follows:
•
Hold down the DVE transition key in the Transition panel of the respective ME
and
•
Press DVE1 or DVE2 of the Aux bus delegation to assign the DVE device to
the respective ME.
Note: Each DVE (DVE1 or DVE2) may only be selected as type of transi-
tion in one ME for one picture component.
Effect selection After Remote has been enabled in the DVE, the desired DVE sequence is selected
with the wipe effect keys in the Wipe panel of the switcher. DD5 and DD10 are
switched over to DVE operation by disabling the functions (keys) Wipe1, Wipe2 or
Mask. Below one of the digipots DVE is displayed.
The wipe keys of a DD20 switcher correspond to the DVE snapshot numbers 1-15
or, when the 2nd key is actuated, to the snapshots 16 - 30.
The DD5 switcher features less keys for the wipe or sequence selection.
The selectable sequence numbers are as follows:
1. bank 1 - 4 2. bank 6- 9 3. bank 11 - 14
with the 2nd key
1. bank 16 - 19 2. bank 21 - 24 3. bank 26 - 29
In the DD20 and DD30 switchers, the Wipe panel is switched over to DVE operation
control with the DVE1 or DVE2 delegation keys. Below one of the digipots DVE is
displayed.
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
Mode 1
FX Loop ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
If the DVE transition type key is actuated, DVE is selected as transition for a picture
component. In this case the assigned DVE device is controlled automatically and
the video and key signal is switched to the DVE device for the respective picture
component. The Loop mode is enabled automatically.
Note: In order to assign the DVE transition mode to a different picture com-
ponent, a different transition type, e.g. Mix or Wipe must be selected
for the original picture component. If DVE transition is selected, it is
not possible to change the transition component as is usual e.g. with
the Mix or Wipe transition.
It is particularly important to monitor this particularity when working
with a DD5 switcher as there are no displays above the keys for pic-
ture component.