THOMSON DD10, Руководство по установке

Страница: 11 / 179

Contents Diamond digital
II
Page Page
6. Initial installation 61 . . . . . . . . . . . . . . . . . . . . .
6.1 Installation checklist 61 . . . . . . . . . . . . . .
6.2 Powerup of the switcher 62 . . . . . . . . . . .
6.3 Input processor RY1900 65 . . . . . . . . . .
6.4 ME processor RY1903 66 . . . . . . . . . . . .
6.5 Key processor RY1906 67 . . . . . . . . . . .
6.6 Wipe processor RY1908 70 . . . . . . . . . .
6.7 Output processor RY1911 71 . . . . . . . . .
6.8 Controller RY1917 72 . . . . . . . . . . . . . . .
6.9 Store RY1913 73 . . . . . . . . . . . . . . . . . . .
6.10 System messages and adjustments 74
6.10.1 Control panel controller
RY1821/RY1822 74 . . . . . . . . . .
6.10.2 E-box controller
RY1601/RY1917 77 . . . . . . . . . .
6.10.3 Fader connector panel
RC1855 81 . . . . . . . . . . . . . . . . . .
6.10.4 Timing/Genlock aligment 82 . . .
6.10.5 Genlock adjust. with menu 84 . .
6.11 Diamond digital-Software update 86 . . .
6.12 Loading flash software from
DD floppy disk drive 94 . . . . . . . . . . . . . .
7. Description of the interfaces 97 . . . . . . . . . .
7.1 Cheapernet specification 97 . . . . . . . . . .
7.2 Router inreface with BTS-
ASCII-Protocol
98 . . . . . . . . . . . . . . . . . . .
7.2.1 General 98 . . . . . . . . . . . . . . . . . .
7.2.2 Interfaces 99 . . . . . . . . . . . . . . . .
7.2.3 Connection cables 100 . . . . . . . .
7.2.4 Menu settings 101 . . . . . . . . . . . .
7.3 Ident X-bar interface 108 . . . . . . . . . . . . .
7.4 Aux panel and under monitor
display installation
110 . . . . . . . . . . . . . .
7.5 Connection of the status
displays RP 1/2 UMD
113 . . . . . . . . . . .
7.6 Tally and GPI interface 117 . . . . . . . . . .
7.7 Function of tally in connectors 124 . . . .
8. DVE and editors 125 . . . . . . . . . . . . . . . . . . . . .
8.1 Technical setup and wiring 125 . . . . . . .
8.2 Preparations at the DVE device 126 . . .
8.3 Device specific notes 127 . . . . . . . . . . .
8.3.1 Pinnacle prizm 127 . . . . . . . . . . .
8.3.2 ABEKAS A-57 VTR protocol 128
8.3.3 ABEKAS A-57
RS232 protocol
129 . . . . . . . . . .
8.3.4 ABEKAS A53D 130 . . . . . . . . . .
8.3.5 QUESTECH charisma 131 . . .
8.3.6 GVG DPM 700 132 . . . . . . . . . .
8.3.7 AMPEX ADO 100/500/1000 134
8.4 DVE control 135 . . . . . . . . . . . . . . . . . . . .
8.5 Editors with GVG-200 o/e protocol 139
8.6 Editors with GVG-100 protocol only 139
8.7 Port protocols in the
diamond digital switchers
140 . . . . . . . . .
8.8 System intergration DD5/DD10 141 . . .
8.9 System intergration DD20/DD30 142 . .
9. Port protocols GVG-200 emulation 143 . . .
9.1 Crosspoint bus command C1-C4 143 . .
9.2 Analog control 144 . . . . . . . . . . . . . . . . . .
9.3 Key (button) commands 145 . . . . . . . . . .
9.4 Key commands 147 . . . . . . . . . . . . . . . . .
9.4.1 Borderline mode command
(B0/B1)
147 . . . . . . . . . . . . . . . . .
9.4.2 Key accumulation command
(BF/CO)
147 . . . . . . . . . . . . . . . .
9.5 Wipe generator commands 148 . . . . . . .
9.5.1 Wipe pattern select
command (C8)
148 . . . . . . . . . . .
9.5.2 Wipe modulation
command (B5)
148 . . . . . . . . . . .
9.5.3 Wipe multiplication
command (B6)
148 . . . . . . . . . . .
9.5.4 Wipe rotation
command (B7)
148 . . . . . . . . . . .
9.5.5 Transition mode
command (CA)
148 . . . . . . . . . . .
9.5.6 Auto transition rate
command (CC, CD)
149 . . . . . .
9.5.7 Transition key select (FB) 149 .
9.5.8 All stop command (F2) 149 . . . .
9.6 Section: E-MEM commands 150 . . . . . .
9.6.1 E-MEM LEARN/RECALL
enable command (D8)
150 . . . .
9.6.2 LEARN E-MEM
command DA)
150 . . . . . . . . . . .
9.6.3 RECALL E-MEM
command (DB)
152 . . . . . . . . . . .
10.Block diagrams 153 . . . . . . . . . . . . . . . . . . . . .