manualshive.com logo in svg

Thermo Scientific Thermolyne NCAT F85930, Инструкция по установке и эксплуатации

Поделиться
Скачать
Thermo Scientific Thermolyne NCAT F85930 Скачать руководство пользователя страница 81

Thermo Scientific

NCAT Asphalt Content Tester         

79

18

Ordering Procedures

Please refer to the Specification Plate for the complete model number, serial number, and series 
number when requesting service, replacement parts or in any correspondence concerning this unit.

All parts listed herein may be ordered from the Thermo Scientific dealer from whom you purchased 
this unit or can be obtained promptly from the factory. When service or replacement parts are needed 
we ask that you check first with your dealer. If the dealer cannot handle your request, then contact our 
Customer Service Department at 800-438-4851.

Prior to returning any materials, please contact our Customer Service Department for a “Return 
Materials Authorization” number (RMA). Material returned without an RMA number will be refused.

Decontamination Statement

We cannot accept any product or component sent to the factory for repair or credit that is 
contaminated with or has been exposed to potentially infectious agents or radioactive materials. No 
product or component will be accepted without a “Return Goods Authorization” (RGA) number.

Содержание Thermolyne NCAT F85930































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды