manualshive.com logo in svg

Thermo Scientific Thermolyne NCAT F85930, Инструкция по установке и эксплуатации

Поделиться
Скачать
Thermo Scientific Thermolyne NCAT F85930 Скачать руководство пользователя страница 62

14

  Hidden Key Routines

60

         NCAT Asphalt Content Tester

Thermo Scientific

9 Key-Disables Beep:

Weight Key-Prints Out Balance Variables:

Enter Key-Prints Out User Variables:

Access:

Depress the 9 key while simultaneously depressing Power Switch to “ON”.

Procedure:

The Chamber Temperature will display BEEP. The Percent Loss window 
will display “ON” or “OFF”. The mode condition will display for three 
seconds. Accessing toggles the mode between “ON” and “OFF”. The 
displayed mode is the active mode. The default mode is BEEP “ON”.

The beep should only be deactivated when the tester is used in the Manual 
Test Mode. The beeper should always remain active when the tester is in 
Auto Mode.

Exit:

The option to inactivate the beeper is useful for raw aggregate calibration 
when minute losses may cause the endpoint beeps to activate prematurely 
before the procedure has been completed. The key press beep is not 
disabled in the BEEP “OFF” mode.

Access:

Depress the weight key while simultaneously depressing the Power Switch 
to “ON”.

Procedure:

The Percent Loss Window will display SCAL. The Elapsed Time window 
will display LIS. The printout will generate automatically upon entering 
the printout mode. See example of factory printout for balance variables on 

page 32

.

Exit:

The furnace will automatically return to normal operation after the 
printout is generated.

Access:

Depress the ENTER Key while simultaneously depressing the Power 
Switch to “ON”.

Procedure:

PRN will display in the Percent Loss window. USR will display in the 
Elapsed Time window. The printout will generate automatically upon 
entering the printout mode.

Exit:

The furnace will automatically return to normal operation after the 
printout is generated.

Содержание Thermolyne NCAT F85930































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды