manualshive.com logo in svg

Thermo Scientific Thermolyne NCAT F85930, Инструкция по установке и эксплуатации

Поделиться
Скачать
Thermo Scientific Thermolyne NCAT F85930 Скачать руководство пользователя страница 28

6

  Installation

The Balance Default Settings When Used in the Type F85900 NCAT Furnace:

26

         NCAT Asphalt Content Tester

Thermo Scientific

7. Press the balance “ENTER” key, [2d Yr] (Two digit year) or [4d Yr] (Four digit year) will be 

displayed.

8. Press the balance “ON/OFF” key until the desired format is displayed.

9. Press the balance “ENTER” key, [dAY XX] (Day) will be displayed.

10. Press the balance “ON/OFF” key until the desired day is displayed.

11. Press the balance “ENTER” key, [nn0 XX] (Month) will be displayed.

12. Press the balance “ON/OFF” key until the desired month is displayed.

13. Press the balance “ENTER” key, [Yr XX] (Year) will be displayed.

14. Press the balance “ON/OFF” key until the desired year is displayed.

15. Press the balance “ENTER” key, the balance will return to the normal weight display.

To Span Calibrate the Balance

1. Switch the green power switch down to “OFF”.

2. After furnace has cooled to room temperature, open the furnace door.

3. Remove and clean any debris from the ceramic load plate, balance load plate, and ceramic support 

posts, replace posts and plates.

4. While holding the “4” key down, switch the green power switch up to “ON”, the red display 

should indicate [BAL CAL].

5. Press and hold the balance “ON/OFF” key.

6. Press the balance “ENTER” key, then release both keys. [71nE] will be displayed, press the balance 

“ON/OFF” key twice, [CAL] will be displayed.

7. Press the balance “ENTER” key, [LOAd 8000] will be blinking on the display.

8. Place an 8000 gram (NIST traceable) weight on the ceramic load plate in the furnace.

9. Press the balance “ENTER” key, the balance will display [ACAL], then return to the normal 

weight display.

To Set Factory Defaults

1. Switch the green power switch down to “OFF”.

2. While holding the “4” key down, switch the green power switch up to “ON”, the red display 

should indicate [BAL CAL].

3. Press and hold the balance “ON/OFF” key.

4. Press the balance “ENTER” key, then release both keys. [71nE] will be displayed, press the balance 

“ON/OFF” key three times, [FACdEF] will be displayed.

Furnace door should remain open during the balance calibration.

Содержание Thermolyne NCAT F85930































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды