manualshive.com logo in svg

Thermo Scientific Thermolyne NCAT F85930, Инструкция по установке и эксплуатации

Поделиться
Скачать
Thermo Scientific Thermolyne NCAT F85930 Скачать руководство пользователя страница 12

2

  Introduction

Introduction

10

         NCAT Asphalt Content Tester

Thermo Scientific

Congratulations on your purchase of a Thermo Scientific Thermolyne NCAT Asphalt Content Tester.

Introduction

The unit is designed to perform a specific test within your laboratory. Please read the instructions 
carefully to ensure that you receive maximum benefit from it. Also, be sure to fill out and return the 
enclosed warranty registration card. We would like to receive the information requested, and it will 
help us assure you of proper warranty coverage.

Intended Use

The NCAT Asphalt Content Tester is an analyzer which determines the asphalt content of a sample by 
loss on ignition per standard methods. The asphalt sample is bathed in oxygenated air and weighed 
continuously throughout the ignition procedure. The NCAT Asphalt Content Tester’s software 
identifies the endpoint of ignition and indicates the completion of the test. Results are documented by 
a printer.

General Usage

Do not use this product for anything other than its intended usage.

Software Updates

Software improvements are initiated based on market feedback. Currently your tester contains Revision 
H software. You will be notified by your sales representative, distributor or the manufacturer as a 
software improvement becomes available. A software packet includes installation instructions, 
operational data and an EPROM. The EPROM is easy to install and can be installed within a few 
minutes.

Theory of Operation

The furnace is heated to a setpoint temperature within the range of 450° - 550°C. The hot mix asphalt 
sample is weighed, equally divided and placed in two screened baskets which are mounted on a tray 
assembly. This complete assembly is placed on the furnace hearth tray. The hearth tray is mounted on 
four ceramic support tubes, which are in turn mounted on a digital balance platform. A blower draws 
ambient air through the four ceramic tube support openings located on the chamber floor. This 
oxygenated air saturates the spread asphalt sample to promote ignition and ashing. The released 
volatiles are further oxidized while passing through a ceramic filter heated to 750°C in a chamber above 
the main chamber. Five air exit ports direct the exhausted air to a louvered plenum. The exhaust is then 
cooled by mixing with ambient air. The blower then directs the exhaust through the plenum exhaust 
port. Standard seamless exhaust tubing directs the exhaust to an outside exhaust system.

Содержание Thermolyne NCAT F85930































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды