manualshive.com logo in svg

Thermo Scientific Thermolyne NCAT F85930, Инструкция по установке и эксплуатации

Поделиться
Скачать
Thermo Scientific Thermolyne NCAT F85930 Скачать руководство пользователя страница 63

 

14  

Hidden Key Routines

Thermo Scientific

NCAT Asphalt Content Tester         

61

Calibration Factor Key-Adjust or Check Test Stability Threshold of a Test:

Temp Key - Toggles from Auto Program Switching Idle to Manual Program 
Switching to Idle at Endpoint:

Access:

Depress the Calibration Factor Key while simultaneously depressing the 
Power Switch to “ON”.

Procedure:

The stability threshold setting will be displayed in the Percent Loss window. 
The Elapsed Time window will display FLN. The value options are 0.01 - 
0.5%. Enter the new value via keypad. Observe the Percent Loss window as 
the new value is entered. The new value must be entered and the ENTRY 
key must be depressed within five seconds.

ASTM Draft 6 specifies test endpoint completion when the measured mass 
loss does not exceed 0.01% over three consecutive one minute periods. 
AASHTO specifies endpoint completion when the mass loss does not 
exceed 0.02% over two consecutive one minute periods. The test stability 
threshold value defines the endpoint. The value must match the standard 
specification you are applying. The test stability value is printed on the User 
Variable Printout. See Hidden Key ENTER. An example of the printout is 
depicted on

 page 32

.

Exit:

Depress Power Switch to “OFF” and then “ON” to return furnace to 
normal operation.

Access:

Depress TEMP key while simultaneously depressing the Power Switch to 
“ON”.

Procedure:

AU appears in the Chamber Temp display. The Percent Loss displays either 
“ON” or “OFF”. Repeat ACCESS if “OFF” is displayed. Repeating access 
changes the display to AU “ON”. You are now in the Auto Program 
Switching to Idle mode. Repeat ACCESS again to return to the Manual 
Program Switching to Idle mode.

Auto Program Switching to Idle can increase the number of tests run per 
day. The operator’s monitoring time is eliminated as the test results 
automatically print out at endpoint. The Manual Program Switching to 
endpoint is still available in the event continuous running is required after 
endpoint.

Exit:

AU “ON” or “OFF” is displayed for approximately five seconds. The 
furnace automatically returns to idle.

Содержание Thermolyne NCAT F85930































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды