Thermo Scientific Thermolyne NCAT F85930 Скачать руководство пользователя страница 57

Страница: 57 / 94

Explanation of Error Codes

Setra Balance Error Codes

Thermo Scientific

NCAT Asphalt Content Tester

Setra Balance Error Codes

Displayed in green Balance indicator window.

HHHHHH

Exceeds maximum specified load. Remedy: Reduce loads to specified
range.

LLLLLL

Load does not meet minimum specified load requirements. Remedy:
Increase load to specified range.

NOCAL

Unable to do span calibration (load not within 1% of cal weight, or
weight unstable).

UnABLE

Unable to process command (usually due to being in improper mode).

ProtEc

Calibration protect switch not in the PROTECT position during
operation.

REPlug

System not calibrated.

OFLO

Internal arithmetic overflow.

S Err

Processor stack overflow.

In Err

Memory indexing error.

E011

Filter thermocouple leads reversed. Thermocouple is type “K”. Polarity
is coded as red (-) and yellow (+). Polarity must be consistent throughout
the circuit.

E012

Balance not communicating; weight, time and date not received. This
may be caused by the balance not being configured correctly. Follow the
procedure

“The Balance Default Settings When Used in the Type

F85900 NCAT Furnace:”

page 25.

Содержание Thermolyne NCAT F85930































































































Результаты поиска

Содержание Thermolyne NCAT F85930

Отзывы:

Бренды по названию

Популярные бренды

Thermo Scientific Thermolyne NCAT F85930, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Thermolyne NCAT F85930

Отзывы:

Бренды по названию

Популярные бренды