manualshive.com logo in svg

Thermo Scientific Thermolyne NCAT F85930, Инструкция по установке и эксплуатации

Поделиться
Скачать
Thermo Scientific Thermolyne NCAT F85930 Скачать руководство пользователя страница 52

12

  Serial Port Output/Operation

Serial Port Output/Operation

50

         NCAT Asphalt Content Tester

Thermo Scientific

Serial Port Output/Operation

The furnace has a serial output port on the rear of the unit. The port outputs a data string to any 
computer able to receive RS232 serial communications. A one-way cable to connect the computer with 
the furnace is needed, along with software on the computer to collect the data. graphAct Data Logging 
and Graphing Software will automatically collect and graph data from the computer for you. If you are 
interested in the graphACT Data Logging Software, contact KG Systems at (201) 429-9300 or fax 
them at (201) 429- 2298. Order computer cable from the manufacturer or your Thermo Scientific 
distributor. Other software, such as “Terminal” in Microsoft Windows™, can be used to collect and 
manipulate the raw data from the furnace. Raw data collected in this manner can be graphed and 
manipulated in a spreadsheet program such as Lotus 123™.

Sample Data Serial Port Output

On the next page are two lines of sample data output. Each line contains the data output of a single 
second of the test cycle, sampled once every minute. The data output can be either continuous or just 
output during a test. To change, see 

“Hidden Key Routines” 

on 

page 57

.

Содержание Thermolyne NCAT F85930































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды