Thermo Scientific ModulyoD Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 30

background image

17

Fit an oil mist filter or pipe the exhaust gases of the vacuum pump to a chemical
fume hood.

All Thermo

Electron

high vacuum pumps are supplied with a gas ballast oil return kit

(GBORK) and EMF10 oil mist filter. Refer to specific manuals received with your
Thermo

Electron

pump to install these items.

3.6

PUMP OUTLET SAFETY

WARNING: Never engage the vacuum pump when water is present in the Ice
Condenser. The introduction of water directly into the internal mechanism of
the vacuum pump will cause significant damage to the pump.

CAUTION:

Do not attempt to use the ModulyoD if it fails the installation test.

If you do, poor performance may result in the loss of the sample being
freeze dried.

Use the following procedure to test the ModulyoD:

If any of the checks below fail, turn the mains switch (item 4, Figure 2) off, then switch
off the external electrical supply and disconnect the supply from the ModulyoD.
Contact your supplier for advice. Do not attempt to use the ModulyoD.

3.7

TEST AFTER INSTALLATION

2

1

3

4

9

10

5

6

7

8

1. Vacuum pump connector
2. Elbow
3. Steel tube
4. Vacuum hose
5. Nozzle connector (optional)
6. Centering-ring and inlet filter assembly
7. Clamp (optional)
8. Thermo

Electron

LyoPump

TM

9. Alternative elbow position
10. Alternative steel tube position

Figure 9 — CONNECT A VLP195FD OR
VLP120 PUMP TO THE M

ODULYO

D

«
...
15
16
17
18
19
...
»

Содержание ModulyoD































Отзывы:

Нет отзывов

Похожие инструкции для ModulyoD

FX-ARM CONTROLLER

Бренд: Magicfx Страницы: 16

Бренд: THORLABS Страницы: 44

Бренд: Parr Instrument Страницы: 24

Бренд: JBL Страницы: 15

Бренд: Baileigh Industrial Страницы: 40

Бренд: Garelick Страницы: 2

Бренд: Garelick Страницы: 2

Бренд: Gardigo Страницы: 32

Бренд: IEMCA Страницы: 82

KID 80-IV Touch

Бренд: IEMCA Страницы: 122

Бренд: Calrec Страницы: 92

Бренд: TANDBERG Страницы: 23

Бренд: KaVo Страницы: 4

ORTHOPANTOMOGRAPH OP 3D

Бренд: KaVo Страницы: 40

KEY Laser III 1243

Бренд: KaVo Страницы: 103

EXTRAmatic 9040

Бренд: KaVo Страницы: 56

ESTETICA E70 Vision

Бренд: KaVo Страницы: 48

Бренд: Kaya Safety Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды