Thermo Scientific ModulyoD Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 30

background image

Qty Description

Check

✓

1

ModulyoD Freeze Dryer

❐

1

Power cord

❐

1

Power cord for pump

❐

1

Instruction Manual

❐

15

Table 3 - Checklist of components

WARNING: Use proper lifting technique to lift ModulyoD.

3.0

INSTALLATION

If the ModulyoD is not to be used immediately, replace the protective cover on the
accessory flange. Store the ModulyoD in a clean, dry area until ready for use.

Remove all packing and inspect the ModulyoD. If the ModulyoD is damaged, notify
your supplier and the carrier in writing within three days; state the Serial Number of the
ModulyoD together with your order number, and your supplier’s invoice number. Retain
all packing materials for inspection. Do not use the ModulyoD if it is damaged.

Check that your package contains the items listed in Table 3, below. If any of these
items are missing, notify your supplier in writing within three days.

3.1

UNPACK AND INSPECT

The ModulyoD is designed for use on a laboratory benchtop. Locate the ModulyoD in
its required operating position, within convenient access to a suitable electrical supply.

We recommend leaving an air-gap of at least 200 mm (8 in) between all four
sides of the ModulyoD and any wall or obstruction. If you do not leave a sufficient air-
gap, poor cooling of the ModulyoD may result in poor performance. When locating the
ModulyoD, consider ease of access for maintenance and repair work, which may
require removing the cover of the ModulyoD.

3.2

SITE PREPARATION

«
...
13
14
15
16
17
...
»

Содержание ModulyoD































Отзывы:

Нет отзывов

Похожие инструкции для ModulyoD

Бренд: Makerfire Страницы: 10

Бренд: Datalogic Страницы: 48

Бренд: PageFlip Страницы: 32

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 20

Бренд: Ultimate Healthcare Страницы: 2

Бренд: Ultimate Healthcare Страницы: 40

Бренд: Vahterus Страницы: 31

Бренд: Valmar Страницы: 78

Бренд: Valhalla Scientific Страницы: 64

Бренд: Waterpik Страницы: 2

Бренд: WaterUps Страницы: 2

Бренд: zapco Страницы: 14

Einthoven CR1000

Бренд: ACE Solution Страницы: 29

Бренд: ParaBody Страницы: 15

Бренд: ParaBody Страницы: 13

Tidland Performance Series

Бренд: Maxcess Страницы: 72

Бренд: Dr.X Works Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды