background image

25

The refrigerant used in the ModulyoD is heavier than air and is an asphyxiant by the 
displacement of oxygen. If a refrigerant leak is suspected, place the unit in a well-ven-
tilated area.  Do not allow naked flames or smoking near the ModulyoD, as products of
combustion of the refrigerant include dangerous fluorides and chlorides.

If refrigerant vapor is inhaled, summon medical help immediately. Take the victim to a 
well-ventilated, uncontaminated area. If the victim's breathing is weak or has stopped,
call for medical attention, apply artificial ventilation, preferably using an oxygen resus-
citator.  Do not use adrenaline or other cardiac stimulants.

At normal atmospheric pressure, the refrigerant will evaporate at -40 ˚C. Contact with 
skin or eyes can cause cold burns. If contact has taken place, seek medical help imme-
diately and carry out the following:  Remove clothing from the affected area; carefully
irrigate the affected area with tepid water for at least 15 minutes; apply a sterile dress-
ing and treat the wound as you would a heat burn. 

5.3

REFRIGERANT LEAKS

6.0

ACCESSORIES

DRYING ACCESSORIES (Appendix B, p. 26)

Accessory

Item # 

Catalog #

8-port column manifold

1

F05656000

16-port drum manifold

2  

F05628000

24-port drum manifold 

3

F05621000

24-port column manifold

4

F05622000

Bell Jar

5

F02960000

VC45 Vial Cell Stoppering shelf unit

6

F05623000

Heater kit for VC45/Stoppering Shelf-115VAC 60Hz

7

F05655115

Heater kit for VC45/Stoppering Shelf-230VAC 50Hz

8

F05655000

Spin Freezer 230V/50Hz

9

F05637000

Spin Freezer 115V/60Hz

10

F05637115

Secondary drying manifold, basic single column

11

F02964000

Secondary drying manifold, additional single column

11

F02956000

Secondary drying manifold, double column

11

F02965000

Pipeline attachment

12

F05660000

Acrylic cylinder

13

F05652000

Acrylic lid

14

F05632000

Rack Assembly

15

F05629000

Product Tray

16

F05630000

Heater Mat

17

F05631000

Temperature Controller-115V/60Hz

18

F05633115

Temperature Controller-230V/50Hz

19

F05633000

Specimen Dryer

20

F02910000

Adapter Flange

21

F05626000

Isolation Valve

22

F05643000

Содержание ModulyoD































Отзывы: