Thermo Scientific Barnstead GenPure xCAD Plus System Скачать руководство пользователя страница 96

Страница: 96 / 128

Maintenance

Change the ultrafilter

GenPure

Thermo Scientific

Change the ultrafilter

(applicable only for systems with UF)

Step

Action

Figure

Switch the GenPure xCAD Plus System off and
shut off the supply of feedwater.

Remove the four screws of the back panel.

Remove carefully the back panel from the system
and unscrew the yellow ground wire from the
back panel.

Pull out the hoses 8 mm by unscrew the
two fittings (see red arrows).

b. After this procedure draw out the

ultrafilter from the mounting clamp (see
red arrow).

Hold with one hand the hose and with
the other hand turn in clockwise
direction the ultrafilter to unscrew the
hose connection.

d. When you are finished with step c install

the new ultrafilter by attaching hoses and
mounting it in the clamp.

When you are installing the new UF
filter the flow arrow of the filter must be
pointing to the bottom of the system.

Reinstall the back panel, reopen the feedwater
supply and switch on the system again.

Feedwater supply

Screws

Hose

Ultra
Filter

White
O-ring

Fitting

Mounting
clamps

Ultra
Filter

White
O-ring

Fitting

Feedwater
supply

Содержание Barnstead GenPure xCAD Plus System

































































































































Результаты поиска

Содержание Barnstead GenPure xCAD Plus System

Отзывы:

Похожие инструкции для Barnstead GenPure xCAD Plus System

Бренды по названию

Популярные бренды

Thermo Scientific Barnstead GenPure xCAD Plus System, Руководство по эксплуатации

Результаты поиска

Содержание Barnstead GenPure xCAD Plus System

Отзывы:

Похожие инструкции для Barnstead GenPure xCAD Plus System

Бренды по названию

Популярные бренды