Thermo King SGCO 3000 Скачать руководство пользователя | Manualshive

Страница: 113 / 144

background image

Engine Maintenance

113

Belt Tension Adjustment and
Belt Replacement

NOTE: Belt tension specifications are measured
using Thermo King belt gauge tool, P/N
204-427.

Belts should be regularly inspected during unit
pretrip for wear, scuffing or cracking and correct
tension.

Correct belt tension is critical for correct unit
operation. Belts that are too loose will slip, squeal
or whip causing excessive vibration levels and
poor unit performance. Belts that are too tight will
put too much strain on the belt fibers and
bearings, causing premature belt and bearing
failures. New belts should be tensioned cold.

NOTE: DO NOT attempt to remove or install
belts without loosening adjustments. Belts that
are installed by prying will fail prematurely due
to internal cord damage.

The water pump belt tension should read 15 to 35
on the belt tension gauge.

1. Remove the nuts from the water pump pulley.

2. Remove the pulley sliding section and add or

remove shims to adjust the belt tension.

3. Reinstall the belt on the pulley and replace the

sliding pulley section on the pulley.

4. Tighten the mounting nuts on the water pump

pulley.

5. The belt tension should read 15-35 on the belt

tension gauge.

NOTE: When adjusting the belt tension using
shims and adjustable pulleys, the belt may still
feel loose when the belt tension gauge indicates
the correct tension. Allow 18 to 25 mm (0.75 to
1.0 inch) deflection with 3 to 4 kg (6 to 9 lb) of
force.

WARNING: DO NOT jump belts on by
cranking the engine. Personal injury may
result.

WARNING: DO NOT attempt to adjust
belts with the unit operating.

WARNING: With the unit On/Off switch
in the “ON” position, the unit may start
operation at any time without prior
warning. Switch unit On/Off switch to
“OFF” position before performing
maintenance or repair procedures.

Water Pump Pulley (Items 1 - 5)

1.

Fixed Pulley Section

2.

Spacer

3.

Shims (4)

4.

Sliding Pulley Section

5.

Nut (4)

6.

Belt

7.

Crankshaft Pulley

Figure 91: Water Pump Fan Belt

AJA2086

1

2 3 4 5

7

6

«
...
111
112
113
114
115
...
»

Содержание SGCO 3000

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для SGCO 3000

FM RDS/DAB Digital Radio RD-50CFM

Бренд: Roberts Страницы: 20

Бренд: Mase Generators Страницы: 92

Бренд: Zodiac Страницы: 31

Onan GenSet 3.ORDJA

Бренд: McGraw-Edison Страницы: 159

Бренд: SMC Networks Страницы: 40

Бренд: Magnum Страницы: 52

QAS 500 Volvo S2A APP

Бренд: Atlas Copco Страницы: 114

Бренд: QFX Страницы: 4

Бренд: Black Max Страницы: 40

Бренд: Memorex Страницы: 2

Бренд: Champion Страницы: 43

Бренд: Whisper Tech Страницы: 98

Бренд: Tektronix Страницы: 6

Бренд: Tektronix Страницы: 12

Public Alert WX-150

Бренд: First Alert Страницы: 16

Бренд: iHome Страницы: 2

Бренд: iHome Страницы: 5

Бренд: iHome Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды