Thermo King SGCO 3000 Скачать руководство пользователя

Страница: 23 / 144

Specifications

SG+ controller uses a sensor to provide engine high coolant temperature protection.

Engine

Diesel Engine Model

TK486V (Tier 2)

Fuel Type

No. 2 Diesel fuel under normal conditions
No. 1 Diesel fuel is acceptable cold weather fuel

Oil Capacity
Crankcase and Oil Filter:

12.3 litre (13 qt)
Fill to full mark on dipstick

Oil Type:

Classification:

Multi-grade Petroleum Oil (Standard)
Synthetic Oil (Optional) after first 500 hours
API Type CI-4 or better
ACEA Type E3 or better

Oil Viscosity:
Below -30 C (-22 F):
-30 C to +50 C (-22 F to +122 F):
-25 C to +30 C (-13 F to +86 F):
-25 C to +40 C (-13 F to +104 F):
-15 C to +40 C (+5 F to +104 F):
-10 C to +50 C (+14 F to +122 F):

SAE 0W-30 (Synthetic)
SAE 5W-40 (Synthetic)
SAE 10W-30
SAE 10W-40
SAE 15W-40
SAE 15W-40 (Synthetic)

Engine Oil Pressure

120 to 320 kPa (1.2 to 3.2 bar) (18 to 47psi)

Engine RPM:
No Load:

1890 ± 10 RPM (High Speed)
1560 ± 5 RPM (Low Speed EcoPower Option only)

Valve Clearance

0.15 to 0.25 mm (0.006 to 0.010 in.)

Valve Setting Temperature

21 C (70 F) (Room Temperature)

Low Oil Pressure Switch (Normally Closed) 117 ± 21 kPa (1.17 ± 0.21 bar) (17 ± 3 psi)

High Coolant Temperature Switch*

Sensor*

Engine Thermostat

71 C (160 F)

Coolant System Capacity

9.5 liter (10 qt) with overflow tank

Engine Coolant Type

Texaco ELC (Extended Life Coolant) or equivalent: ELC red
coolant, 50/50 antifreeze and water mixture, not to exceed 60/40

Radiator Cap Pressure

90 kPa (0.90 bar) (13 psi)

Fan/Water Pump Belt Tension
New or Field Reset:

15 to 35 tension number on belt tension gauge,
TK P/N 204-427; or 19 to 25 mm (0.75 to 1.0 in.) deflection with 3 to
4 Kg (6 to 9 lb) of force

Generator

Type

460/230 Vac, 3 Phase, 60 Hz

Output Power

15 kw

Kilovolt-Amperes

18.75 kVA

RPM

1800 RPM

Содержание SGCO 3000
















































































































































Результаты поиска

Содержание SGCO 3000

Отзывы:

Похожие инструкции для SGCO 3000

Бренды по названию

Популярные бренды

Thermo King SGCO 3000, Руководство пользователя

Результаты поиска

Содержание SGCO 3000

Отзывы:

Похожие инструкции для SGCO 3000

Бренды по названию

Популярные бренды