CESSNA
SECTION 9 - SUPPLEMENTS
MODEL 172S NAV III
SUPPLEMENT 3
KAP 140 AUTOPILOT
U.S.
FAA APPROVED
NORMAL PROCEDURES
(Continued)
MISSED APPROACH
1. A/P DISC/TRIM INT Switch - PUSH to disengage the autopilot
2. Missed Approach Procedure - EXECUTE
3. If autopilot is to be engaged:
a. Elevator Trim - SET
b. Airspeed and Rate of Climb - STABILIZED
WARNING
THE G1000 WILL ENTER SUSP MODE (STOP THE
FLIGHT PLAN) AT THE MISSED APPROACH POINT
(MAP) AND WILL NOT SUPPLY A NAVIGATION SIGNAL
TO THE KAP 140. IF THE G1000 IS TO BE USED FOR
COURSE GUIDANCE TO THE MISSED APPROACH
HOLDING POINT (MAHP), PUSH THE SUSP SOFTKEY
TO START THE FLIGHT PLAN AND NAVIGATION
SIGNAL AGAIN BEFORE ENGAGING THE KAP 140.
NOTE
•
Only engage the autopilot during wings-level stable
flight. The autopilot will come on in ROL (wings leveler)
and VS (Vertical Speed) modes. The VS mode initial
rate-of-climb will be the vertical speed at the time the
autopilot is engaged. Do not engage the autopilot when
the airplane cannot hold the climb rate because of
excessive pitch attitude, low airspeed, low engine power
or high airplane weight. Do not engage the autopilot
when the performance or operation of the autopilot or
airplane would not obey the limitations.
•
The autopilot can hold a vertical speed selection only if
engine power and airplane weight are correct for the
conditions. If the vertical speed set for the autopilot is
more than the airplane can supply and airspeed
decreases sufficiently, the airplane can be made to stall.
Make sure that the vertical speed set for the autopilot
results in airplane performance that stays in the
operating limitations of both the autopilot and the
airplane.
(Continued Next Page)
172SPHAUS-S3-01
S3-43
For
Training
Purposes
Only
Содержание Cessna 172S NAV III Skyhawk SP
