background image

READ THROUGH THIS MANUAL BEFORE STARTING CONSTRUCTION. IT CONTAINS IMPORTANT

INSTRUCTIONS AND WARNINGS CONCERNING THE ASSEMBLY AND USE OF THIS MODEL.

WARRANTY

Great Planes

®

 Model Manufacturing Co.

 guarantees this kit to 

be free from defects in both material and workmanship at the 
date of purchase. This warranty does not cover any component 
parts damaged by use or modification. 

In no case shall Great 

Planes’ liability exceed the original cost of the purchased kit.

 

Further, Great Planes reserves the right to change or modify this 
warranty without notice.

In that Great Planes has no control over the final assembly or 
material used for final assembly, no liability shall be assumed nor 
accepted for any damage resulting from the use by the user of 

the final user-assembled product. By the act of using the 
user-assembled product, the user accepts all resulting liability.

If the buyer is not prepared to accept the liability associated 
with the use of this product, the buyer is advised to return 
this kit immediately in new and unused condition to the 
place of purchase.

To make a warranty claim contact:

greatplanes.com/support

Wingspan:

78.5 in [1995mm]

Weight:

29– 31 oz [822– 879 g]

Length:

42 in [1065mm]

Wing Area:

498 in

2

 [32.1 dm

2

SPECIFICATIONS

INSTRUCTION  MANUAL

Radio:

4+ ch. radio, 4 servos

(Servos included with the Rx-R)

Battery:

2S 2200mAh,
3S 1800mAh LiPo

(LiPo not included)

Propeller:

12 x 6.5 (included)

Wing

Loading:

8.4 – 9.0 oz /ft2
[25.6– 27.5 g /dm2]

Motor:

RimFire .10 Outrunner

(Included with the Rx-R)

ESC:

40A

(Included with the Rx-R)

GPMA1818/GPMA1819

© 2018 Great Planes Model Mfg. A subsidiary of Hobbico,

®

 Inc.

Содержание Tori





















Отзывы: