TEXIO PSF-1200L Скачать руководство пользователя страница 35

Страница: 35 / 121

5-2-2. Connection with the front output terminals

(1) Shut off the POWER switch.
(2) Connect crimp style lug terminals to the ends of the load cables.

Fix the load cables firmly to eliminate looseness or backlash from
the front output terminals and load cables.

(3) Protect the front output terminals with the protective caps

supplied with the product for safety, if current is output through
the rear output terminals.

(Good)

(Bad)

Fig.5-5 Connection with Front Output Terminals

CAUTION

●

The power supply unit may output a maximum of 40A through the

front output terminals. Do not use pin plugs or banana plugs for

outputting large current in order to avoid overheat due to contact
resistance. Use lug terminals that meet the output currentrating

and connect them firmly with the front output terminal.

●

For safety, NEVER output power through both the front and rear

output terminals.

Содержание PSF-1200L


























































































































Результаты поиска

Содержание PSF-1200L

Отзывы:

Похожие инструкции для PSF-1200L

Бренды по названию

Популярные бренды

TEXIO PSF-1200L, Инструкция по эксплуатации

Результаты поиска

Содержание PSF-1200L

Отзывы:

Похожие инструкции для PSF-1200L

Бренды по названию

Популярные бренды