Texi Fox 25, Руководство пользователя

Страница: 178 / 200

RU
ВНИМАНИЕ: Не оставляйте включенной машины без присмотра. После окончания
работы всегда вытягивайте шнур из розетки. Следует выключить машину перед чисткой.
ВНИМАНИЕ: При отключении машины из сети не вытягивайте вилку за шнур, возьмите
за вилку и выньте ее из электрической розетки.
Если педаль отключена, нельзя начать процесс пошива.
НОЖНОЙ ПРИВОД (ПЕДАЛЬ)
СВОБОДНЫЙ РУКАВ
ПОДЪЁМ ЛАПКИ
Для начала работы нажмите на педаль. С помощью
педали регулируется скорость шитья. Чем сильнее
вы нажимаете на педаль, тем быстрее машина
шьет.
Отодвиньте платформу-приставку влево,
как показано на рисунке ниже.
После снятия платформы получаем
свободный рукав, который облегчает шитье
труднодоступных мест (рукава и т.п.)
Доступны три положения лапки
1. Лапка должна быть всегда опущена во время
шитья.
2. Лапку необходимо поднять (до среднего
положения), чтобы положить материал.
3. Лапку можно поднять до третьего наивысшего
положения, удерживая рычаг, с целью
размещения под лапкой нескольких слоев
материала либо при смене лапки.
3
2
1
3
5
4
7
6
8
9
KNOWING YOUR SEWING MACHINE
Power line cord/foot control
Make sure that the sewing machine is turned off (the
power switch is set to “O”), and then connect the plug
of the power line and into the appliance inlet and your
wall outlet.
The foot that comes on your sewing machine
is called zigzag foot and will be used for the
majority of your sewing.
Setting up your machine
Bu sure to wipe off any surplus oil from needle
plate area before using your machine the first
time.
Power/light switch
Your machine will not operate until the power/light switch is turned on. The same switch controls
both the power and the light.
When servicing the machine, or changing needles, etc., machine must be disconnected from
the power supply.
NOTE
:
When foot control is disconnected,
the machine will not operate.
Always disconnect the machine from power
supply by removing the plug from the wall-outlet.
Sewing speed can be varied the foot control.
The harder you press on the control, the faster
machine runs.
Accessories
1. Bobbins (3pcs)
2. Needle 3 pcs and twin needle 1 pc
3. Multi-function screwdriver
4. Seam guide(optional)
5. Ripper/Brush
6. Buttonhole foot
7. Guide presser foot
8. Zipper foot
9. Button fitting foot
Power/light
switch “OFF” Power/light
switch “ON”
4
2
1
3
KNOWING YOUR SEWING MACHINE
Converting to free
-
arm sewing
Your machine can be used either as a flat-bed or as a
free-arm model.
With the extension table in position, it provides a
large working surface as a standard flat-bed model.
To remove the extension table, hold it firmly with both
hands and pull it off to the left as shown. To replace,
slide the extension table back into place until it
clicks.
With the extension table removed the machine
converts into a slim free-arm model for sewing
children’s clothes, cuffs, trouser legs, and other
hard-to-reach places.
Presser foot lifter
There are three positions for your presser foot.
1. Lower the presser foot to sew.
2. Raise the lifter to the middle position to insert or remove
fabric.
3. Lift it to its highest position to change the presser foot or to
remove thick fabric.
Reverse sewing lever
As long as you are pressing down this
button while sewing, the machine will feed
the fabric backwards.
Dropping the feed dogs
1. For dropping the feed dogs, press down
lever and move it to the direction of arrow
as illustrated.
2. To raise the feed dogs, press down the
lever and move it to the direction or arrow
as illustrated.
* Feed dogs must always be up for normal
sewing.
4
2
1
3
KNOWING YOUR SEWING MACHINE
Converting to free
-
arm sewing
Your machine can be used either as a flat-bed or as a
free-arm model.
With the extension table in position, it provides a
large working surface as a standard flat-bed model.
To remove the extension table, hold it firmly with both
hands and pull it off to the left as shown. To replace,
slide the extension table back into place until it
clicks.
With the extension table removed the machine
converts into a slim free-arm model for sewing
children’s clothes, cuffs, trouser legs, and other
hard-to-reach places.
Presser foot lifter
There are three positions for your presser foot.
1. Lower the presser foot to sew.
2. Raise the lifter to the middle position to insert or remove
fabric.
3. Lift it to its highest position to change the presser foot or to
remove thick fabric.
Reverse sewing lever
As long as you are pressing down this
button while sewing, the machine will feed
the fabric backwards.
Dropping the feed dogs
1. For dropping the feed dogs, press down
lever and move it to the direction of arrow
as illustrated.
2. To raise the feed dogs, press down the
lever and move it to the direction or arrow
as illustrated.
* Feed dogs must always be up for normal
sewing.
Texi Fox 25 178