TESA MH3D Скачать руководство пользователя страница 89

Страница: 89 / 102

User's Manual

MH3D

Page 5-21

Glossary

Spline

The interpolation of a series of functions between two
given data points, for all the points in the set.

Squareness

Deviation of the axes from 90° in their relationship to
each other.

Staging

The moving of a gage from first position to second
position.

Static

Motionless.

Statistical Analysis

The examination of numerical information.

Step Gage

A gage consisting of a rigid bar with calibrated steps
used for determining the accuracy of distance measure-
ments in a direction of linear motion.

Straightness

A measurement routine that computes the deviation of a
line from true straightness. Also, the deviation of an axis
from a perfect path.

Store

To save information into a computer memory.

Stylus

The portion of a probe that contacts the part. Usually a
synthetic ruby ball mounted on a steel shank.

Symmetry

The midpoint between two features. A symmetry feature
is the mathematical bisector of two features.

Systematic Error

That portion of a machine error that results from com-
puting the mean of a very large number of similar
measurements.

Taper Probe

A type of rigid probe used primarily for hole location.

Target

In DCC, a specified point on the part that is being
measured.

Target Tolerance

A zone around each specified target that allows for

Zone

minor errors in the position of the target.

Temperature

An estimate of the maximum possible measurement

Variation Error

error induced solely by deviation of the environment
from average thermal conditions.

Tertiary Datum

The datum established by at least one point of contact
between a datum feature and the inspection surface.

Tolerance

Limiting values added to nominal dimensions that allow
variations of a measured feature.

Содержание MH3D
















































































Результаты поиска

Содержание MH3D

Отзывы:

Бренды по названию

Популярные бренды

TESA MH3D, Руководство пользователя

Результаты поиска

Содержание MH3D

Отзывы:

Бренды по названию

Популярные бренды