TESA MH3D Скачать руководство пользователя страница 73

Страница: 73 / 102

User's Manual

MH3D

Page 5-5

Glossary

Booting a System

The process of activating or loading the software into the
computer. Powering the computer system so that the
operating software becomes functional.

Boss

A circular raised projection on the surface of the work
piece.

Bridge

The bridge is an inverted “U” shaped member that
moves in the Y direction and supports the X and Z
moving members.

Buffer

A storage (holding) area in a computer for measurement
data.

CAD/CAM

Computer-Aided Design, Computer-Aided Manufacture.

Calibrate

To adjust a measuring instrument or inspect it for
accuracy.

Calibration Sphere

An accessory used in qualifying the probe. A master
sphere.

Cartesian

Feature output expressed as X, Y, and Z.

Cartesian

A system used to describe points in space in terms of X,

Coordinates

Y, and Z axes. The axes are perpendicular to each other.
The points are expressed in relation to some fixed origin
(zero point).

Cartesian Coordinate

A measuring system that uses three independent,

Measuring System

mutually perpendicular, axes to form a grid. The
coordinates of a point are measured as distances from
each of these axes.

Centroid

The weighted center of all points that make up an
element.

Character

Any letter, number, or punctuation mark that can be
typed from a keyboard or displayed on a screen.

Circle

A geometric element defined by a minimum of three
points equidistant from a centerpoint. A measurement
routine used to compute the diameter and location of a
bored hole or a cylinder.

Circle-Circle

A measurement routine which computes the shortest

Distance

two-dimensional distance (working plane) between 2
circle center points.

Circularity

The condition of a circle as it lies in a tolerance zone
formed by two concentric circles. Also called roundness.

Содержание MH3D
















































































Результаты поиска

Содержание MH3D

Отзывы:

Бренды по названию

Популярные бренды

TESA MH3D, Руководство пользователя

Результаты поиска

Содержание MH3D

Отзывы:

Бренды по названию

Популярные бренды