manualshive.com logo in svg

TESA MH3D, Руководство пользователя

Поделиться
Скачать
TESA MH3D Скачать руководство пользователя страница 100

©2004 TESA Switzerland All Rights Reserved.

Page A-8

User's Manual

MH3D

CCD Optical Probe - Qualification

Note: In order to use a RAM Optical Probe with MH3D you will have to install a
desk mouse in addition to the ZMouse. This is because the RAM Optical Probe
covers the buttons of the ZMouse. Select the "System Options" softkey and the
"Languages, etc." and change the mouse type to "Desk Mouse".

Probe Qualification

To qualify the optical probe:

1.

Turn the MH3D electronic box "Off" and then "On".

2.

Remove the probe from the Z-rail.

3.

Clamp the MH3D qualification sphere to the granite table in the right
rear corner (or any location where it will not interfere with the part being

measured).

4.

Home the MH3D and press "Done".  Tell the system it has an optical
probe.

5.

Place the MH3D Z-rail on the qualification sphere and press "Done".

6.

Clamp the optical probe in the Z-rail.

7.

Align the crosshairs on the monitor screen to the X-axis and the Y-axis

of the MH3D.

8.

Focus the probe on the equatorial plane of the qualification sphere using
the lowest magnification.

9.

Take three measurement points equally spaced on the circumference
(refer to the following section on measuring with the optical probe).

10. Focus the probe on the top point of the sphere and bring this point to the

origin of the reference crosshair on the monitor screen.

11. Take a measurement point and press "Done".

Part Alignment

To perform a part alignment:

1.

Select "Measurements" from the Main Menu.

2.

Focus on the plane to be measured by moving the probe towards the
part (as if measuring with a hard probe).

3.

Focus on and measure at least three points on the working plane spaced
as far apart as practical.  Press "Done".

4.

If a direction point is requested, elevate the probe and take it.  This will

insure the consistent orientation of the part coordinate system.

5.

Select the "Set Level" softkey.

6.

Focus on and measure at least two points to define the major axis. Press

"Done".

7.

Select the "Set Axis" softkey.

8.

Measure either a point or a circle to define the origin. Select the "Set
Origin" softkey.

Содержание MH3D







































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды