TESA MH3D Скачать руководство пользователя страница 14

Страница: 14 / 102

Page 1-10

User's Manual

MH3D

13. Z MOUSE - Used with the control box for menu selection, measurement

point taking, scanning and for data input.

14. AIR SUPPLY - Provides and distributes air to the air bearings for

smooth, frictionless travel of the bridge, carriage and Z rail. The air
supply is also used for the adjustable Z rail counterbalance.

15. AIR BEARINGS - The air bearings provide noncontact, frictionless

movement of the bridge, carriage, and Z rail along their respective ways.

16. MEASURING SYSTEM - A highly accurate, opto-electric system, con-

sisting of a scale and an encoder head, which sends electronic signals to
the readout as it moves along the scale.

17. MACHINE LEVELING FEET - Three screws and pads used to isolate

the machine from vibrations and to level the machine.

18. ANTI-TIP BOLTS - Two bolts in the machine base that prevent the

machine from tipping if it is bumped or has an unbalanced load.

19. GRANITE LEVELING FEET - Three ball-end screws in the top of the

base that provide a three point support for the table. They are also used
to level the granite to the X and Y axes.

20. FINE ADJUSTMENT - Allows precise adjustment of all three axes by

means of knurled knobs .(Optional)

Description

Содержание MH3D
















































































Результаты поиска

Содержание MH3D

Отзывы:

Бренды по названию

Популярные бренды

TESA MH3D, Руководство пользователя

Результаты поиска

Содержание MH3D

Отзывы:

Бренды по названию

Популярные бренды