manualshive.com logo in svg

TESA MH3D, Руководство пользователя

Поделиться
Скачать
TESA MH3D Скачать руководство пользователя страница 47

User's Manual

MH3D

©2004 TESA Switzerland All Rights Reserved.

Page 3-13

Probe Installation

The Z-rail has a probe holder built into
the bottom of the rail.  To install a hard
probe:

1. Loosen the locking lever on the

side of the Z-rail.

2. Insert the probe shank into the

Z-rail.  A spring plunger detent
will help to hold the probe in
place (the probe tip is normally
3" (75mm) from the end of the
Z-rail).

3. Tighten the locking lever.  Be

sure the probe is firmly clamped.

4. Adjust the Z-rail counterbalance

control to compensate for the
added weight of the probe.  Unlock
the Z-axis.  Unlock the counterbalance regulator by pulling the knob

outward.  When finished, push the knob in.

To install a Touch Trigger Probe:

1. Loosen the locking lever on the side of the Z-rail.

2. Check the Touch Trigger Probe to be sure it has a stylus tip.  If not, obtain

the required tip and install it onto the probe head sensing shaft, securing
the tip with the stylus tool provided.  Refer to the probe manufacturer's
documentation for stylus installation instructions.

3. Insert the probe head mounting shaft into the Z-rail until it engages the

detent.

4. Rotate the probe head until the red light indicator faces the front of the

machine.

5. Hold the probe in this position and tighten the locking lever until the

probe is firmly clamped.

6. Connect the probe head lead to the probe connector located on the Z-rail.

7. If necessary, adjust the Z-rail counterbalance control to compensate for

the change in weight from the probe.  The proper tip type must be selected
in the MH3D software.

Note: These probe installation procedures are typical and included as an
example.  The procedure for installing your probe may differ from these.  Refer
to your probe manufacturer's documentation for installation instructions.
Note: Each tip must be qualified before it it used for measurements.

Probe
Locking
Lever

Z-rail

ZMouse

Содержание MH3D







































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды