manualshive.com logo in svg

TESA MH3D, Руководство пользователя

Поделиться
Скачать
TESA MH3D Скачать руководство пользователя страница 65

Page 4-9

©2004 TESA Switzerland All Rights Reserved.

User's Manual

MH3D

Machine Troubleshooting

Machine won’t repeat measurement

• Are excessive vibrations occurring in the area of the machine?
• Is the part secure on the table?
• Is the probe tight in Probe Holder? Check that locking knob is tightened.
• Is the probe broken?
• Verify that the trigger force is correct for the stylus length. An incorrectly

adjusted stylus is a source of non-repeatability.

• Shorter stylus lengths will give more repeatable results than longer stylus..
• Review your probing technique.
• Is the diameter of the stylus ball too small? Make sure the stem of the stylus

does not hit against the part being measured.

• Is the temperature of the part, machine and the measuring environment stable

and within specification?

• Is the TP2 (if supplied) screwed tightly into the probe body?
• Is the stylus screwed in tightly?
• Is the probe shanking on the part?
• Is the proper measurement plane selected (XY, YZ, ZX)?

Inaccurate measurements

• Is the part dirty or oily?
• Is the surface finish on the part poor? Using a larger diameter stylus ball will

reduce the effect of surface finish of the part being inspected.

• Was the homing/initialization procedure followed correctly?
• Is an unqualified tip being used?
• Has the tip been moved after qualification?
•  Has the qualification sphere been moved since the first tip was qualified? The

reference offsets and tip 1 measurements must be repeated if sphere is moved.

• Has the probe been damaged?
• Check the temperature of the part, machine and the measuring environment.

Are they stable and within specification?

Probe does not take hits

• Are the cables correct and properly connected?
• Is the TTP enabled? See Software Manual for details.
• Is the probe interface (PI-6) loose or not present?
• Has the probe reseated? The red light on the probe should blink off and on each

time a hit is registered. If the light remains off after a hit has been taken, gently
move the stylus or the probe with your finger. The probe light should turn back
on.

• Are the machine and control box cables correct and properly connected?

Содержание MH3D







































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды