User's Manual
MH3D
©2004 TESA Switzerland All Rights Reserved.
Page 3-5
Operator Safety
• Never lay tools on the machine where they can interfere with its
operation.
• Before using the machine, look for workpiece or other obstructions.
• Report any unusual noise from the machine. Defects should be repaired
immediately.
Never operate the machine in a defective condition.
• Before mounting work holding devices or workpieces, be sure that all
mounting surfaces are clean and free of chips, particularly the bearing
surfaces.
• Keep hands away from all guards and openings in covers when moving
the bridge or carriage.
• Tables, rails, housings and their related parts can create pinch points. Be
sure you are clear of such locations before operating the MH3D.
• Never remove WARNING and/or INSTRUCTION plates from the
machine.
• During service, it may be necessary to remove or open some guards. If
so, use great caution around exposed mechanisms. Make sure all guards
are returned and in place when set-up work is completed.
• Do not allow the bridge, carriage or rail to impact the end stops with a
high amount of force at the ends of the measuring range. Bring the
machine to a gentle stop.
• Do not allow the probe body or Z-rail to strike the workpiece or work
table.
• Do not allow the probe to strike the workpiece with high force. Refer-
ence the probing technique section of this manual.
• Do not attempt to move the bridge, carriage, or Z-Rail while air pressure
is below the value listed in the specification section. Serious damage to
the machine will result. Do not attempt to move the machine with the
axes switches down.
• Always hold the Z rail firmly when unlocking the Z axis lock.
• Lock the machine axes when the machine is not in use.
Содержание MH3D
