Terex Genie Z-80/60 Скачать руководство пользователя

Страница: 73 / 80

Fifth Edition • First Printing

Operator's Manual

Transport and Lifting Instructions

Part No. 1294418GT

-80/60

Observe and Obey:



Only qualified riggers should rig the machine.



Only certified crane operators should lift the
machine and only in accordance with the
applicable crane regulations.



Be sure the crane capacity, loading surfaces
and straps or lines are sufficient to withstand
the machine weight. See the serial label for
the machine weight.

Lifting Instructions

Fully lower and retract both the primary and
secondary booms. Remove all loose items on the
machine.

Rotate the turntable 90 degrees.

Determine the center of gravity of your machine
using the picture on this page.

Attach the rigging only to the designated lifting
points on the machine.

Attach the rigging to the 2 chassis lifting points
farthest from the turnable lifting point.

Adjust the rigging to prevent damage to the
machine and to keep the machine level.

Turntable Lifting Point

Chassis lifting Points (2)

Center of Gravity Y Axis

Center of Gravity X Axis

Center of Gravity Z Axis

Содержание Genie Z-80/60

















































































Результаты поиска

Содержание Genie Z-80/60

Отзывы:

Похожие инструкции для Genie Z-80/60

Бренды по названию

Популярные бренды

Terex Genie Z-80/60, Руководство оператора

Результаты поиска

Содержание Genie Z-80/60

Отзывы:

Похожие инструкции для Genie Z-80/60

Бренды по названию

Популярные бренды