Terex Genie Z-80/60 Скачать руководство пользователя страница 32

Страница: 32 / 80

Operator's Manual

Fifth Edition • First Printing

Controls

-80/60

Part No. 1294418GT

Platform Control Panel

Horn button

Press this button and the horn will sound.
Release the button and the horn will stop.

Platform not level indicator light

Level the platform until the light is off. The
platform level toggle switch will only work in
the direction that will level the platform.

Machine on incline indicator light

Light on indicates all functions have stopped.
See the instructions in the Operating
Instructions section.

Lower primary boom indicator light

Lower the primary boom until the light is off.

Not used

Used for optional equipment

Generator control with indicator light (if
equipped)

Move the switch or press the button to turn the
generator on. Move the switch again or
release the button to turn the generator off.

Содержание Genie Z-80/60

















































































Результаты поиска

Содержание Genie Z-80/60

Отзывы:

Похожие инструкции для Genie Z-80/60

Бренды по названию

Популярные бренды

Terex Genie Z-80/60, Руководство оператора

Результаты поиска

Содержание Genie Z-80/60

Отзывы:

Похожие инструкции для Genie Z-80/60

Бренды по названию

Популярные бренды