Terex Genie Z-80/60 Скачать руководство пользователя страница 61

Страница: 61 / 80

Fifth Edition • First Printing

Operator's Manual

Operating Instructions

Part No. 1294418GT

-80/60

Drive Enable

Light on indicates that the boom
has moved just past either
circle-end wheel and the drive
function is turned off.

To drive, push the drive enable button or move the
drive enable switch to either side and slowly move
the drive/steer control handle off center.

If the drive/steer control handle is not moved within
two seconds of activating the drive enable. the
drive function will not operate. Release and active
the drive enable again.

Be aware that the machine may move in the
opposite direction that the drive and steer controls
are moved.

Always use the color-coded direction arrows on
the platform controls and the drive chassis to
identify the direction the machine will travel.

Generator (if equipped)

To operate the generator, press the generator
button or move the switch. The indicator light will
come on the engine will continue to run.

Plug a power tool into the power to platform GFCI
outlet.

To turn off the generator, press the generator
button or move the switch. The indicator light will
turn off.

Engine Idle Select (rpm)

Select engine idle (rpm). Push the button or move
the switch. The indicator light next to the current
setting will be on.



Rabbit and foot switch symbol: foot switch
activated high idle



Turtle symbol: low idle



Rabbit symbol: high idle

Check Engine Light

Light on and engine stopped: Tag
the machine and remove from
service.

Light on and engine still running:
Contact service personnel within
24 hours.

Содержание Genie Z-80/60

















































































Результаты поиска

Содержание Genie Z-80/60

Отзывы:

Похожие инструкции для Genie Z-80/60

Бренды по названию

Популярные бренды

Terex Genie Z-80/60, Руководство оператора

Результаты поиска

Содержание Genie Z-80/60

Отзывы:

Похожие инструкции для Genie Z-80/60

Бренды по названию

Популярные бренды