Terex Genie Z-80/60 Скачать руководство пользователя | Manualshive

Страница: 20 / 80

background image

Operator's Manual

Fifth Edition • First Printing

Work Area Safety

18

Z

®

-80/60

Part No. 1294418GT

Do not place or attach
fixed or overhanging loads
to any part of this
machine.

Do not place ladders or
scaffolds in the platform or
against any part of this
machine.

Do not transport tools and materials unless they
are evenly distributed and can be safely handled
by person(s) in the platform.

Do not use the machine on a moving or mobile
surface or vehicle.

Be sure all tires are in good condition, air-filled
tires are properly inflated and lug nuts are properly
tightened.

Do not use the platform controls to free a platform
that is caught, snagged, or otherwise prevented
from normal motion by an adjacent structure. All
personnel must be removed from the platform
before attempting to free the platform using the
ground controls.

Operation on Slopes Hazards

Do not drive the machine on a slope that exceeds
the maximum uphill, downhill or side slope rating
of the machine. Slope rating applies only to
machines in the stowed position.

Maximum slope rating, stowed position, 2WD

Platform downhill

30%

(17°)

Platform uphill

15%

(9°)

Side slope

25%

(14°)

Maximum slope rating, stowed position, 4WD

Platform downhill

45%

(24°)

Platform uphill

35%

(19°)

Side slope

25%

(14°)

Note: Slope rating is subject to ground conditions
with one person in the platform and adequate
traction. Additional platform weight may reduce
slope rating. See Driving on a Slope in the
Operating Instructions section.

«
...
18
19
20
21
22
...
»

Содержание Genie Z-80/60

















































































Отзывы:

Нет отзывов

Похожие инструкции для Genie Z-80/60

Бренд: Presto Lifts Страницы: 16

Бренд: Presto Страницы: 24

Бренд: Terex Страницы: 62

Бренд: RUDETRANS Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды