Terasic TR10a-HL Скачать руководство пользователя

Страница: 57 / 112

Make sure the Nios II EDS and USB-Blaster II driver are installed.

Make sure the FPGA board and PC are connected with an UBS Cable.

Power on the FPGA board.

Copy the “Demonstrations/PFL/flash_programming_batch” folder under the
CD to your PC’s local drive.

Execute the batch file flash_program.bat to start flash programming.

Power off the FPGA Board.

Set FPGA configure mode as FPPx32 Mode by setting SW1 MSEL[0:2] to

000.

Specify configuration of the FPGA to Factory Hardware by setting the

FACTORY_LOAD dip in SW1

to the ‘1’ position.

Power on the FPGA Board, and the Configure Done LED should light.

Except for programming the Flash with the default code PFL, the batch file also writes

PFL (Parallel Flash Loader) Option Bits data into the address 0x30000. The option bits

data specifies 0x2B40000 as start address of your hardware design.

The NIOS II EDS tool nios-2-flash-programmer programs the Flash based on the

Parallel Flasher Loader design in the FPGA. The Parallel Flash Loader design is

included in the default code PFL and the source code is available in the folder

Demonstrations/ PFL in System CD.

Содержание TR10a-HL

















































































































Результаты поиска

Содержание TR10a-HL

Отзывы:

Похожие инструкции для TR10a-HL

Бренды по названию

Популярные бренды

Terasic TR10a-HL, Руководство пользователя

Результаты поиска

Содержание TR10a-HL

Отзывы:

Похожие инструкции для TR10a-HL

Бренды по названию

Популярные бренды