Tennant 7400 Скачать руководство пользователя страница 80

Страница: 80 / 92

MAINTENANCE

7400 (GM) 330970 (12--03)

TRANSPORTING THE MACHINE

1. Position the rear of the machine at the

loading edge of the truck or trailer.

2. If the loading surface is not horizontal or is

higher than 380 mm (15 in) from the ground,

use a winch to load machine.

If the loading surface is horizontal AND is

380 mm (15 in) or less from the ground, the

machine may be driven onto the truck or

trailer.

3. To winch the machine onto the truck or

trailer, attach the winching chains in the

holes at the bottom of the rear bumper.

If the machine has the optional rear tie down

brackets, attach the winching chains to

them.

4. Turn the bypass valve 90

from the normal

position before winching the machine onto

the truck or trailer. See

PUSHING OR

TOWING THE MACHINE

section of this

manual. Make sure the machine is centered.

FOR SAFETY: When loading machine

onto truck or trailer, use winch. Do not

drive the machine onto the truck or

trailer unless the loading surface is

horizontal AND is 380 mm (15 in) or less

from the ground.

Содержание 7400





























































































Результаты поиска

Содержание 7400

Отзывы:

Похожие инструкции для 7400

Бренды по названию

Популярные бренды

Tennant 7400, Руководство оператора

Результаты поиска

Содержание 7400

Отзывы:

Похожие инструкции для 7400

Бренды по названию

Популярные бренды