Tennant 7400 Скачать руководство пользователя страница 65

Страница: 65 / 92

MAINTENANCE

7400 (GM) 330970 (12--03)

SCRUB BRUSHES

Two cylindrical scrub brushes span the width of

the scrub head, sweeping debris into the debris

tray while scrubbing the floor. The scrub brushes

should be checked daily for tangled wire or string,

wear, and damage.

The scrub brushes can be rotated front-to-rear,

and end-for-end to increase brush life.The

brushes should be replaced if large portions of the

brush bristles are missing or if the remaining

brush bristles measure 15 mm (0.50 in) in length.

NOTE: Cylindrical scrub brushes must be

installed with the V--patterns on the brushes

pointing towards each other for best debris pick

up.

NOTE: Be sure to replace the scrub brushes in

sets. Otherwise one scrub brush will be more

aggressive than the other.

Содержание 7400





























































































Результаты поиска

Содержание 7400

Отзывы:

Похожие инструкции для 7400

Бренды по названию

Популярные бренды

Tennant 7400, Руководство оператора

Результаты поиска

Содержание 7400

Отзывы:

Похожие инструкции для 7400

Бренды по названию

Популярные бренды